Key takeaways
- Who certifies testers depends on the state: Texas requires a backflow prevention assembly tester license after an approved course and exam[1].
- The UPC requires testing at installation, repair or relocation and at least annually, following ASSE Series 5000 procedures[2].
- Field test kits must meet ASSE 1064, and test reports usually go to the public water supplier[1][2].
- With about 18% of plumbers aged 55 or older, shops should certify younger techs to keep testing capacity[3].
Why backflow testing is its own credential
A backflow prevention assembly protects the public water supply from contamination when pressure drops or reverses. Assemblies have moving parts, springs and seals that wear, so codes and water suppliers require them to be tested regularly by someone qualified to do it. That tester is not always the same as the plumber who installed the device. In most places, testing requires a separate certification or license, issued by a state agency, a health authority or a recognized certifying body.
For a plumbing company, a certified tester on staff opens recurring work: annual tests for commercial buildings, irrigation systems, fire lines and multifamily properties, plus the repairs that failed tests produce. It is also a credential customers and water suppliers check before they accept a report.
Three common certification models
| Model | Who issues it | Example |
|---|---|---|
| State license | A state environmental or health agency | Texas requires testers to complete an approved course, pass an exam and hold a current backflow prevention assembly tester license[1] |
| State health authority certification | The state drinking water program | Oregon's 2026 code requires testing by a backflow assembly tester certified by the Oregon Health Authority[2] |
| Professional qualification standard | A national standards or certification body, often accepted by water suppliers | The UPC calls for testers qualified under the ASSE/IAPMO/ANSI Series 5000 standards[2] |
Many water suppliers also keep their own list of approved testers and require testers to register with them before submitting reports. A tester may need a state certification, a registration with each water supplier and a calibrated test kit before they can test in a given area.
Texas: the backflow prevention assembly tester license
Texas sets its rules in the state's public water system regulations. Required backflow prevention assemblies must be tested upon installation by a licensed backflow prevention assembly tester and certified as operating within specifications[1]. Assemblies that protect against health hazards must be tested at least annually by a licensed tester[1]. To qualify, a tester must complete a course approved by the agency's executive director, pass the executive director's examination and hold a current license[1].
Paperwork matters as much as the test. In Texas, the signed and dated original test report goes to the public water supplier for its records, and the water purveyor keeps copies of inspection and test reports on file[1]. Testers who work on fire lines face an additional condition: they may test firelines only if permanently employed by an approved fireline contractor[1].
Before testing in a new area, ask the water supplier three questions: which tester credentials it accepts, whether testers must register with it, and how it wants test reports submitted.
What the UPC requires
In jurisdictions on the Uniform Plumbing Code, section 603.4.2 sets the testing baseline. The premise owner or responsible person must have the backflow prevention assembly tested by a certified tester at the time of installation, repair or relocation and at least annually after that, or more often where the authority having jurisdiction requires[2]. Periodic testing follows the procedures referenced in the ASSE/IAPMO/ANSI Series 5000 standards, by a tester qualified under those standards, and the field test kit must comply with ASSE 1064[2].
- Annual testing at minimum, with more frequent tests where the local authority requires them.
- Testing after any repair or relocation, not just on the anniversary date.
- Procedures that follow the referenced standards for each assembly type.
- A test kit that meets the referenced standard and is kept accurate.
- Placement rules: the code prohibits installing devices with atmospheric vents or ports in pits, underground or in submerged locations, though a double check valve assembly may be installed below grade[2].
Repair parts matter too. Backflow assemblies on potable water lines are part of the drinking water system, and federal law defines lead free as a weighted average of 0.25% lead across wetted surfaces of pipes, fittings and fixtures[4]. Use the manufacturer's approved repair kits and lead-free parts.
Assembly types every tester must know
Certification courses focus on the testable assemblies a tester will meet in the field. Each has its own purpose, hazard rating and test procedure, and a tester must recognize them quickly on site, often in cramped meter vaults or mechanical rooms.
- Reduced pressure principle assemblies, used for high-hazard connections such as chemical feed, medical and some commercial processes.
- Double check valve assemblies, used for lower-hazard connections and common on fire lines and some domestic services.
- Pressure vacuum breaker assemblies, common on irrigation systems where backsiphonage is the main risk.
- Spill-resistant vacuum breakers, used indoors where a pressure vacuum breaker's discharge would cause problems.
- Detector versions of these assemblies on fire lines, which include a bypass meter to reveal unauthorized use.
Field habits matter as much as classroom knowledge: record readings as you take them, photograph the assembly tag, and note anything unusual about the installation before you leave the site.
Knowing the assembly is only half the job. A good tester also recognizes when the installed device does not match the hazard, such as a double check on a connection that needs a reduced pressure assembly, and reports it to the owner and the water supplier according to local rules.
Insurance, liability and keeping current
A test report is a professional statement that an assembly protected the water supply on that day. Make sure your general liability insurance covers backflow testing and that the policy is listed with any water supplier that requires proof. Keep copies of every report you submit, with test kit details, so you can answer questions later.
Certifications expire. Most programs require renewal on a set cycle, sometimes with a refresher course or practical re-examination, and many require periodic accuracy checks on test kits. Put each tester's renewal date, kit verification dates and supplier registrations on your compliance calendar. A tester who lets a certification lapse cannot submit reports, and the tests on your route stop until it is renewed. Plan training so renewals do not land in your busiest testing months.
Who in your shop should get certified
Backflow testing suits careful, methodical technicians who are comfortable with paperwork. It is also a good role for experienced plumbers who want less heavy lifting. But do not concentrate the credential in your oldest techs. About 115,000 of the 624,000 employed plumbers, pipefitters and steamfitters in 2025, roughly 18%, were 55 or older[3].
- Aged 55 or older 18%
Source: U.S. Bureau of Labor Statistics, 2025[3]
Show the data
| Item | Value |
|---|---|
| Aged 55 or older | 18% |
With about 42,000 openings for plumbers projected each year from 2025 to 2035[5], certified testers are hard to replace when they retire. A practical rule is to keep at least two certified testers for every route's worth of annual tests, with at least one of them early in their career.
Getting certified, step by step
Check the rules where you work
Find the state agency or health authority that certifies testers, and the requirements of the water suppliers you will report to.
Choose an approved course
Enroll in a course accepted by your state and suppliers; most combine classroom theory with hands-on testing of each assembly type.
Pass the exams
Expect written and practical exams covering hydraulics, cross-connection hazards, assembly types and test procedures.
Buy and verify a test kit
Purchase a test kit that meets the referenced standard and set up the accuracy checks your program requires.
Register with suppliers
Submit your certification, kit information and insurance to each water supplier that requires tester registration.
Calendar renewals
Track certification renewal, any refresher course and kit accuracy verification dates.
Example: a fictional commercial plumbing shop, Mesa Grande Plumbing, has one certified tester who is 61. The owner sponsors two technicians in their late twenties through the state-approved course, buys two additional test kits and registers both new testers with the three water suppliers in its service area. Within a year, the shop can cover its annual test list without overtime and has a plan for the senior tester's retirement. Next: building a recurring backflow testing route.
Frequently asked questions
Do I need a plumbing license to test backflow assemblies?
It depends on the state. Some states tie testing to a separate tester license or certification that does not require a plumbing license, while others require both. Check your state agency and local water supplier.
How often must backflow assemblies be tested?
Under the UPC, at installation, repair or relocation and at least annually. Texas requires assemblies protecting against health hazards to be tested at least annually.
Where do backflow test reports go?
Usually to the public water supplier. In Texas, the signed original report goes to the supplier, which keeps copies on file.
What test kit do I need?
The UPC requires field test kits that comply with ASSE 1064. Many programs also require periodic accuracy verification.
References
Legal Information Institute, Cornell Law School (2026). 30 Tex. Admin. Code 290.44: Water Distribution (opens in a new tab) โ
Oregon Building Codes Division (2026). 2026 Oregon Plumbing Specialty Code: Summary of amendments and significant changes (opens in a new tab) โ
U.S. Bureau of Labor Statistics (2025). Labor Force Statistics from the CPS, Table 11b: Employed persons by detailed occupation and age, 2025 (opens in a new tab) โ
U.S. Environmental Protection Agency (2026). Use of Lead Free Pipes, Fittings, Fixtures, Solder and Flux for Drinking Water (opens in a new tab) โ
U.S. Bureau of Labor Statistics (2025-2035). Occupational Outlook Handbook: Plumbers, Pipefitters, and Steamfitters (opens in a new tab) โ