Licensing compliance

Lead-free plumbing rules for products and solder

What 'lead free' means under federal law, which products are exempt, how certification works since 2023, and a van-stock audit plumbers can run this week.

AssistCall research teamPublished Reviewed by Faruque Amin, VP of Sales and Marketing7 min read

On this page
  1. What 'lead free' means in federal law
  2. Why this still comes up on service calls
  3. Certification and marking since 2023
  4. What is covered and what is exempt
  5. Run a van stock and purchasing audit
  6. What to tell customers
  7. Commercial, multifamily and inspection jobs
  8. Common mistakes to avoid
  9. Frequently asked questions
  10. References
Licensing compliance: Lead-free plumbing rules for products and solderArticle coverLICENSING COMPLIANCELead-free plumbingrules for products andsolderAva for PlumbersInsightsLicensing compliance: Lead-free plumbing rules for products and solderArticle coverLICENSING COMPLIANCELead-free plumbingrules for productsand solderAva for Plumbers

Key takeaways

  • Federal 'lead free' means a weighted average of no more than 0.25% lead on wetted surfaces, and no more than 0.2% lead in solder and flux.
  • Since September 1, 2023, products sold as lead free for drinking water must carry third-party certification.
  • Toilets, shower valves, tub fillers, service saddles and nonpotable-only products are exempt, so a 'not lead free' label is not always a problem.
  • Audit van stock and supplier orders once a year, and keep spec sheets for anything installed on a potable line.

What 'lead free' means in federal law

Lead free does not mean zero lead. Under Section 1417 of the Safe Drinking Water Act, a pipe, fitting or fixture is lead free when the wetted surfaces contain a weighted average of no more than 0.25% lead, and solder and flux are lead free at no more than 0.2% lead[1]. Wetted surfaces are the parts that touch the water, so a brass body can still carry some lead in places water never reaches, as long as the weighted average across the wetted area stays under the limit.

The limit used to be far looser. The 1986 amendments allowed pipes and fittings with up to 8% lead, and the Reduction of Lead in Drinking Water Act of 2011 cut that to the 0.25% weighted average used today[1]. Anyone who learned the trade before that change, or who still pulls fittings from an old box at the back of the shop, is working from a different rule.

Maximum lead allowed in 'lead free' pipes and fittingsThe current limit applies to the weighted average across wetted surfaces.
Maximum lead allowed in 'lead free' pipes and fittingsComparison. 1986 amendments: 8%; Current rule (weighted average): 0.25%.8%1986 amendments1986 amendments: 8%0.25%Current rule (weighted average)Current rule (weighted average): 0.25%Maximum lead allowed in 'lead free' pipes and fittingsComparison. 1986 amendments: 8%; Current rule (weighted average): 0.25%.8%1986 amendments1986 amendments: 8%0.25%Current rule (weighted average)Current rule (weighted average): 0.25%

Source: U.S. Environmental Protection Agency, 2026[1]

Show the data
ItemValue
1986 amendments8%
Current rule (weighted average)0.25%

The federal rule is a floor. Some states and local codes adopted lower limits earlier or add their own labeling rules, and your plumbing inspector enforces the local code, not just the federal definition. Check your state code and any local amendments before relying on the federal wording alone.

Why this still comes up on service calls

EPA sets the health goal for lead in drinking water at zero and says there is no safe level of exposure[2]. That is why inspectors, property managers and informed homeowners ask what you are putting on their potable lines. Lead pipes are more likely in older cities and in homes built before 1986[2], which is much of the housing stock many service companies work in every day.

Pipe replacement work is also growing. EPA's latest needs survey estimates about four million lead service lines in the country[3], and the Lead and Copper Rule Improvements require water systems to identify and replace lead pipes within 10 years[4]. More replacement work means more transitions from old piping to new, and every new fitting, valve and solder joint on the drinking water side has to meet the lead-free definition.

4 million

estimated lead service lines still in use in the US[3]

Certification and marking since 2023

EPA published its final lead-free rule on September 1, 2020. It gave manufacturers and importers three years to certify compliance through a consistent verification process, and since September 1, 2023, lead-free certification has been required for the regulated products[1]. In practice that means a third-party certifier has tested or reviewed the product, and the mark appears on the product, the packaging or the spec sheet.

Two standards come up most at the supply house. NSF/ANSI/CAN 372 covers lead content, and NSF/ANSI/CAN 61 covers the wider health effects of drinking water system components. A product can carry one without the other, so read the listing rather than assuming a single logo covers both. When a customer, inspector or facility manager asks, the spec sheet with the certification line is your proof.

Rule of thumb: if a part touches drinking water and you cannot find a lead-free certification on the box or the spec sheet, do not install it on a potable line.

What is covered and what is exempt

The rule has a short list of exemptions. Knowing them stops techs from rejecting good parts and stops buyers from ordering the wrong ones[1].

Coverage under the federal lead-free rule, based on EPA's exemption list.
ProductLead-free rule applies?Field note
Pipe, fittings and valves on potable linesYes, 0.25% weighted averageCheck certification on every new SKU
Solder and fluxYes, 0.2% leadKeep 50/50 solder off the potable truck stock
Kitchen and lavatory faucetsYesCommon source of uncertified imports
Toilets, bidets, urinals, fill valves, flushometer valvesExemptNo lead-free mark needed
Tub fillers and shower valvesExemptExempt even though they carry potable water
Service saddlesExemptUtility-side part
Main gate valves 2 inches and largerExemptDistribution main use
Products used only for nonpotable serviceExemptLabel clearly so they are never used on potable lines

The nonpotable exemption is the one that causes trouble. Irrigation and industrial brass may legally contain more lead, and it looks the same as potable brass once it is out of the bag. Keep it in a separate, labeled bin and never let it ride in the same drawer as potable fittings.

Run a van stock and purchasing audit

  1. Pull every brass and bronze part

    Empty the fittings drawers on each van and in the shop. Anything without a lead-free mark or a traceable SKU goes in a quarantine box.

  2. Check solder and flux

    Remove any solder that is not marked lead free from potable stock. Keep it only if you have a documented nonpotable use.

  3. Match SKUs to spec sheets

    For each regular SKU, save the manufacturer spec sheet showing the lead-free certification in a shared folder the office can reach.

  4. Tell your suppliers

    Ask your counter reps to flag any substitute that lacks certification, and add a line to your purchase orders requiring certified lead-free products for potable use.

  5. Brief the crew

    Spend ten minutes at a morning meeting on the exemption list, so techs know why a shower valve without the mark is fine and a faucet without it is not.

  6. Repeat yearly

    Put the audit on the calendar each year and after any change of supplier.

What to tell customers

Customers rarely ask about weighted averages. They ask whether the new parts are safe and whether the old ones are a problem. Keep the answer short, accurate and free of scare tactics.

  • On new parts: 'Everything we install on your drinking water lines is certified lead free under the federal standard. I can send you the spec sheet if you would like it.'
  • On old brass or solder: 'Older fittings and solder can contain more lead than today's limit. If you want to know what is in your water, your water utility or a certified lab can test it.'
  • On lead pipe: 'This looks like a lead service line. Your water utility may have a replacement program, and I can help you find out what they cover.'

Example: a technician replacing a kitchen faucet in a 1970s house finds galvanized supply piping with old solder joints at the meter. She installs a certified faucet and supply lines, photographs the old joints, and notes on the invoice that the customer may want to ask the utility about the service line material. The note takes one minute and often turns into a quote request later.

Commercial, multifamily and inspection jobs

On commercial and multifamily work the question usually arrives in writing. Submittal packages for schools, clinics and apartment buildings often ask for proof that every potable component is certified lead free, and a general contractor may hold payment until the submittals are approved. Build the habit on residential work and the commercial paperwork becomes routine: the same spec sheet folder answers both.

Inspectors look at the same things a careful customer does. They check that solder on potable lines is lead free, that faucets and valves carry a certification mark, and that nonpotable brass has not crept onto the drinking water side. A failed inspection on a remodel costs a return trip, a re-cut joint and a delayed final, which is far more than the price difference between certified and uncertified parts.

  1. Keep a one-page list of the certified SKUs you install most often, with the certification line for each.
  2. Attach the relevant spec sheets to commercial submittals before the job starts, not after a reviewer asks.
  3. Note on residential invoices that potable components installed are certified lead free.
  4. When a customer supplies their own faucet or fixture, check its listing before installing it, and write on the work order if it lacks one.

Customer-supplied fixtures deserve a clear policy. Online marketplaces sell faucets that never went through certification, and once you install one, the customer will assume you approved it. A short line in your terms that you install customer-supplied parts only when they carry a lead-free certification protects you and gives the tech an easy way to say no.

Common mistakes to avoid

  • Assuming any brass from a reputable brand is lead free. Many lines include nonpotable versions with similar part numbers.
  • Accepting a substitute at the counter without checking the listing.
  • Treating an exempt product as a code violation and upselling an unneeded replacement.
  • Losing the paperwork. If a commercial client or inspector asks for proof months later, you need the spec sheet on file.
  • Telling customers their water is safe or unsafe. You can speak to the parts you installed; water quality is a question for a lab or the utility.

If you also work on drinking water protection devices, the same certification habit applies to your backflow testing program. For the utility side of lead pipes, see our guide to the Lead and Copper Rule Improvements.

Frequently asked questions

Is lead-free brass completely free of lead?

No. Under federal law, lead free means a weighted average of no more than 0.25% lead across the wetted surfaces of pipes, fittings and fixtures, and no more than 0.2% lead in solder and flux.

Do shower valves and toilets need lead-free certification?

No. EPA lists toilets, bidets, urinals, fill valves, flushometer valves, tub fillers and shower valves among the products exempt from the lead-free requirements.

When did lead-free certification become required?

EPA's final rule was published on September 1, 2020, and lead-free certification has been required for regulated products since September 1, 2023.

Can I use old fittings from shop stock on a repair?

Only if you can confirm they meet today's lead-free definition, ideally with a certification mark or spec sheet. Older stock may predate the current limit and should not go on potable lines.

References

  1. U.S. Environmental Protection Agency (2026). Use of Lead Free Pipes, Fittings, Fixtures, Solder and Flux for Drinking Water (opens in a new tab) โ†‘

  2. U.S. Environmental Protection Agency (2026). Basic Information about Lead in Drinking Water (opens in a new tab) โ†‘

  3. U.S. Environmental Protection Agency (2025). EPA's 7th Drinking Water Infrastructure Needs Survey and Assessment (opens in a new tab) โ†‘

  4. U.S. Environmental Protection Agency (2024). Lead and Copper Rule Improvements (opens in a new tab) โ†‘

Book a demo

See Ava handle your calls.

Book a short demo. Weโ€™ll walk through your calls and workflow, and agree what Ava should take care of.

Book a demo