Pricing estimates

Quoting tankless water heater conversions

A survey-to-proposal method for tankless conversions: demand sizing, gas line checks, venting, electrical and a descaling plan written into the quote.

AssistCall research teamPublished Reviewed by Faruque Amin, VP of Sales and Marketing7 min read

On this page
  1. Why conversion quotes go wrong
  2. Start with demand, not the brochure
  3. The four parts of every conversion quote
  4. Gas sizing on the survey visit
  5. Show the options side by side
  6. Write the descaling plan into the proposal
  7. Install-day risks to price before you sell
  8. Be accurate about savings and incentives
  9. Mistakes that cost conversion margin
  10. Questions to ask before the survey
  11. Frequently asked questions
  12. References
Pricing estimates: Quoting tankless water heater conversionsArticle coverPRICING ESTIMATESQuoting tankless waterheater conversionsAva for PlumbersInsightsPricing estimates: Quoting tankless water heater conversionsArticle coverPRICING ESTIMATESQuoting tanklesswater heaterconversionsAva for Plumbers

Key takeaways

  • A tankless conversion quote has four parts that each need a site check: gas supply, venting, electrical and water quality.
  • Size from the number of fixtures running at once and the temperature rise, then show the customer the math.
  • Put a descaling plan and its price in the proposal; hard water is the most common reason a good install turns into a warranty fight.
  • Be accurate about savings and incentives: water heating is one of the year-round energy uses, and the old federal credit ended with 2025 installs.

Why conversion quotes go wrong

A tank-to-tankless conversion is not a swap. The unit needs far more gas while it fires, a different vent, often a new outlet, and water clean enough that its heat exchanger does not scale up in two years. A quote written from a phone call and a model number usually misses at least one of those, and the missing piece shows up as a change order or an unhappy customer standing in a lukewarm shower.

The fix is a survey visit with a fixed checklist, a proposal built in four parts, and a maintenance plan that is priced in from the start rather than mentioned at the end.

Start with demand, not the brochure

Tankless units are sized by flow at a given temperature rise, not by gallons stored. Daily use gives useful context for the conversation: EPA puts average home water use at 82 gallons per person per day[1], and says roughly 70% of an average family's home water use happens indoors[2]. But a unit fails when too many fixtures run at once, so size to the peak.

  1. List the fixtures that run together

    Ask which showers, tubs and appliances realistically run at the same time on a busy morning. Two showers and a dishwasher is a common answer in a family home.

  2. Add their flow rates

    Read the rated flow on the actual fixtures rather than assuming. Older showerheads and body sprays can run far higher than new ones.

  3. Find the temperature rise

    Measure incoming water temperature, or use your local winter ground-water figure, and subtract it from the target outlet temperature.

  4. Match the unit to flow at that rise

    Use the manufacturer's flow chart at the winter rise, not the summer one. If one unit cannot cover the peak, quote two units or a recirculation design.

Example (fictional): two showers rated at 2.0 gallons per minute plus a kitchen faucet at 1.5 gives a peak of 5.5 gallons per minute. With winter inlet water at 45 degrees and a 120-degree target, the rise is 75 degrees. The unit must deliver 5.5 gallons per minute at a 75-degree rise on its published chart.

The four parts of every conversion quote

Survey items for tank-to-tankless conversions. Code and manufacturer requirements take precedence.
PartWhat to check on the surveyCommon findingsHow to quote it
Gas supplyMeter capacity, pipe size and length from meter, other appliances on the lineExisting half-inch line too small for the added loadLine upsizing priced per run, with the sizing table attached
VentingVent path to the outside, distance limits, condensing or non-condensing unitOld chimney cannot be reused; new wall or roof penetration neededVent kit plus penetration; roof work as a separate line
ElectricalOutlet within reach, circuit available, condensate pump powerNo outlet at the heater locationOutlet or circuit by your electrician, quoted as a named line
Water qualityHardness test, existing softener, sedimentHard water with no treatmentIsolation valve kit, descaling plan, optional softener or scale filter

Present each part with its own line and a one-sentence reason. Customers accept a gas line upgrade more readily when they see the sizing logic, and your installer arrives knowing exactly what was sold.

Gas sizing on the survey visit

  • Photograph the meter label and record its rated capacity.
  • Measure the developed length of pipe from the meter to the heater location, including fittings.
  • List every gas appliance on the system with its input rating: furnace, range, dryer, fireplace, pool heater.
  • Add the new unit's maximum input and check the total against your code sizing table for that length.
  • If the meter is undersized, note that the utility may need to upgrade it and that timing is outside your control.

Leave gas sizing until install day and you have a crew standing idle while someone calls the utility. Do it on the survey and the problem becomes a line item the customer approved weeks earlier.

Show the options side by side

Homeowners who call about tankless are often comparing it with a straight tank replacement, and sometimes with a heat pump tank. A proposal that shows two or three options on one page answers the comparison they are already making in their head, and stops them from calling three other shops to make it for them.

  • Option one: a standard tank replacement with all code items, so the customer sees the baseline.
  • Option two: the tankless conversion with each of the four parts listed, plus isolation valves and the first flush visit.
  • Option three, where it fits: the tankless unit with a recirculation pump or scale treatment for homes with long pipe runs or very hard water.
  • Under each option, the expected service needs, the warranty terms and what the customer must do to keep the warranty valid.

Keep the language plain. Endless hot water is a promise you cannot keep if the household runs four fixtures at once on an undersized unit; hot water for the fixtures you told us run together, at the temperature you chose, is a promise you can.

Write the descaling plan into the proposal

Hardness drives maintenance. The U.S. Geological Survey classifies water with 0 to 60 mg/L as calcium carbonate as soft, 61 to 120 as moderately hard, 121 to 180 as hard and more than 180 as very hard[3]. Test the water on the survey and write the band on the proposal.

Hardness bands from USGS. Service intervals are example policies; always follow the unit manufacturer's manual.
Hardness bandUSGS range (mg/L)Example service planWhat to include in the quote
Soft0 to 60Annual inspection and inlet screen cleaningIsolation valves; first-year visit
Moderately hard61 to 120Annual flush and inspectionIsolation valves; annual flush visit priced
Hard121 to 180Flush more often, per manufacturer guidanceFlush plan plus scale-prevention option
Very hardOver 180Treatment strongly advised before installSoftener or scale filter as a recommended line

Isolation valves with service ports cost little and make every future flush a short visit. A flush plan sold at the install also turns a one-time job into recurring work; many shops fold it into a maintenance membership.

Install-day risks to price before you sell

Some surprises appear only when the old tank comes out. Price them as defined contingencies so the installer can proceed without stopping the job to renegotiate.

  • Corroded shutoff valves that break when turned: a fixed price per valve replaced.
  • Wall or roof penetration that hits framing or wiring: a per-hour allowance with a cap the customer approved.
  • Condensate disposal for condensing units where no drain is nearby: a pump option priced on the proposal.
  • Drywall patching and paint around new vent or gas routes: state clearly whether finish work is included or excluded.

A short list like this protects both sides. The customer knows the worst case before signing, and your installer has authority to fix the problem at a known price instead of calling the office from the job.

Be accurate about savings and incentives

Customers often expect a dramatic drop in their energy bill. Give them context instead. EIA groups water heating with lighting and refrigeration as the year-round home energy uses, together 25% of home energy use in 2020, while space heating and air conditioning took 52%[4]. Savings depend on the household's hot water use, fuel prices and the unit being replaced, so avoid promising a figure.

Where household energy goesShare of total annual home energy use, 2020.
Where household energy goesComparison. Space heating and air conditioning: 52%; Water heating, lighting and refrigeration: 25%.52%Space heating and air conditioningSpace heating and air conditioning: 52%25%Water heating, lighting and refrigerationWater heating, lighting and refrigeration: 25%Where household energy goesComparison. Space heating and air conditioning: 52%; Water heating, lighting and refrigeration: 25%.52%Space heating and air conditioningSpace heating and air conditioning: 52%25%Water heating, lighting andrefrigerationWater heating, lighting and refrigeration: 25%

Source: U.S. Energy Information Administration, 2020[4]

Show the data
ItemValue
Space heating and air conditioning52%
Water heating, lighting and refrigeration25%

Incentives need the same care. The IRS says the federal energy efficient home improvement credit, which covered qualifying water heaters, applies to improvements made through December 31, 2025[5]. For 2026 installs, point customers to current state and utility programs instead.

Mistakes that cost conversion margin

  1. Quoting from the model number on the old tank without a survey visit.
  2. Sizing at summer inlet temperature and getting complaints every January.
  3. Forgetting the meter and the other gas appliances when sizing the line.
  4. Leaving isolation valves out to shave the price, then charging more for every future flush.
  5. Promising specific energy savings or an expired tax credit in writing.

Questions to ask before the survey

The booking call should collect enough to send the right person with the right tools. Use a short script and save the answers to the job.

  1. Is your current water heater gas, propane or electric, and roughly how old is it?
  2. Where is it located: garage, basement, attic, closet or outside?
  3. How many bathrooms are in the home, and how many people live there?
  4. Do you have a water softener or any filtration now?
  5. Could you text a photo of the heater, its label and the vent pipe above it?

If the customer is still deciding between tank and tankless, quote both on the same survey. A side-by-side with a standard replacement, priced with the code items in our guide to pricing water heater replacements, lets them choose on facts.

Frequently asked questions

Can I quote a tankless conversion over the phone?

You can give a wide range, but gas sizing, venting and electrical needs make a site survey the only reliable basis for a firm price.

Should the descaling plan be optional?

Make the isolation valves standard and the flush plan a strongly recommended line. In hard water areas, explain that skipping maintenance can affect the manufacturer's warranty.

What if the gas meter is too small?

Note it on the proposal, explain that the utility controls the upgrade and its timing, and schedule the install only after the utility confirms.

Is tankless always the better choice?

No. For some homes a standard or heat pump tank fits the budget, space and use pattern better. Quote the options side by side.

References

  1. U.S. Environmental Protection Agency, WaterSense (2026). WaterSense Statistics and Facts (opens in a new tab) โ†‘

  2. U.S. Environmental Protection Agency, WaterSense (2026). How We Use Water (opens in a new tab) โ†‘

  3. U.S. Geological Survey, Water Science School (2019). Hardness of Water (opens in a new tab) โ†‘

  4. U.S. Energy Information Administration (2020). Use of energy explained: Energy use in homes (opens in a new tab) โ†‘

  5. Internal Revenue Service (2025). Energy Efficient Home Improvement Credit (opens in a new tab) โ†‘

Book a demo

See Ava handle your calls.

Book a short demo. Weโ€™ll walk through your calls and workflow, and agree what Ava should take care of.

Book a demo