Pricing estimates

Pricing and explaining hydro jetting

When hydro jetting is the right call, how to explain it to homeowners and managers, and how to build a jetting price that covers setup, risk and video.

AssistCall research teamPublished Reviewed by Faruque Amin, VP of Sales and Marketing7 min read

On this page
  1. What jetting does that a cable cannot
  2. When jetting is the right tool
  3. Camera first, then decide
  4. How to explain jetting in plain words
  5. Answering the usual objections
  6. Building the jetting price
  7. Commercial grease lines and maintenance contracts
  8. Training techs to offer it at the right moments
  9. Paperwork that protects the job
  10. Frequently asked questions
  11. References
Pricing estimates: Pricing and explaining hydro jettingArticle coverPRICING ESTIMATESPricing and explaininghydro jettingAva for PlumbersInsightsPricing estimates: Pricing and explaining hydro jettingArticle coverPRICING ESTIMATESPricing andexplaining hydrojettingAva for Plumbers

Key takeaways

  • Jetting fits grease, scale, sludge and recurring blockages in sound pipe; it is the wrong tool for broken, offset or fragile lines.
  • A camera inspection before and after jetting is the evidence that sells the job and protects you if the pipe fails later.
  • Price jetting by line-length band or by the hour for commercial work, with setup, water and disposal built in.
  • A short, honest explanation with video converts better than a hard sell, because customers can see what they are paying for.

What jetting does that a cable cannot

A cable machine punches a hole through a blockage. Water flows again, the customer is happy, and the grease, scale or sludge still coating the pipe wall is waiting to catch the next load. Hydro jetting scours the full diameter of the pipe, which is why it suits lines that keep coming back. That difference is the whole sales conversation: a cable clears a path, jetting cleans the pipe.

Because the equipment is expensive and the job takes longer, jetting must be priced and explained differently from a standard drain call. Done well, it becomes one of the highest-value services on a drain truck. Done badly, it becomes a source of disputes about price and, occasionally, about damaged pipe.

When jetting is the right tool

Grease is the classic case. EPA's report to Congress on sewer overflows found that grease from restaurants, homes and industrial sources was the most common cause of reported blockages, at 47%[1]. Use the criteria below on every call where jetting might fit.

  • Good fit: recurring kitchen or main-line clogs caused by grease, soap scum or sludge.
  • Good fit: scale buildup in cast iron that is still structurally sound on camera.
  • Good fit: sand, silt or debris in storm and yard drains.
  • Good fit: root intrusion after the roots have been cut, to flush the remains, where the pipe joints are intact.
  • Poor fit: broken, collapsed or badly offset pipe, where water pressure can make the damage worse.
  • Poor fit: very old clay, pitch fiber or deteriorated cast iron that the camera shows is already failing.
  • Poor fit: lines with no usable cleanout, where access would require extra work the customer has not approved.

Camera first, then decide

  1. Clear enough to see

    If the line is fully blocked, open it with a cable so the camera can travel. Price that step as part of the diagnostic, not as a separate job.

  2. Record the inspection

    Run the camera the full length you plan to jet. Note distances to joints, offsets, bellies and the material of each section.

  3. Show the customer

    Play the key moments on a tablet: the grease coating, the scale, the root mass. Point out anything that makes jetting risky.

  4. Recommend one path

    Jet, repair first, or replace. Give one recommendation with a reason, then the alternatives.

  5. Record the result

    After jetting, run the camera again and save both videos to the job. The after video is your proof of work and your best review prompt.

The before video also protects you. If a weak section fails months later, a recorded inspection showing that you pointed out the risk, and a signed acknowledgment, separates a fair outcome from an argument.

How to explain jetting in plain words

Homeowners and property managers are not buying water pressure; they are buying fewer emergencies. Keep the explanation short and tie it to what they just saw on the screen.

  • What we did today opened the line, but you can see the grease still coating the pipe. That is why it keeps backing up.
  • Jetting uses high-pressure water to clean the whole inside of the pipe, not just a path through the middle.
  • Your pipe looks sound on camera, so jetting is safe here. If I had seen a break, I would recommend a repair first.
  • After we jet, I will run the camera again so you can see the difference before I leave.
  • If you would rather not do it today, here is the price, and it stays good for the next two weeks.

Avoid scare language. A sewer backup is serious enough without exaggeration. Insurance data already makes the point: water damage and freezing claims averaged $15,400 per homeowners claim over 2019 to 2023[2].

Share of insured homes with a claim each yearAverage annual claim frequency for US homeowners insurance, 2018 to 2022.
Share of insured homes with a claim each yearComparison. Wind and hail: 2.8%; Water damage and freezing: 1.6%.2.8%Wind and hailWind and hail: 2.8%1.6%Water damage and freezingWater damage and freezing: 1.6%Share of insured homes with a claim each yearComparison. Wind and hail: 2.8%; Water damage and freezing: 1.6%.2.8%Wind and hailWind and hail: 2.8%1.6%Water damage and freezingWater damage and freezing: 1.6%

Source: Insurance Information Institute, 2019-2023[2]

Show the data
ItemValue
Wind and hail2.8%
Water damage and freezing1.6%

Answering the usual objections

Most hesitation about jetting comes down to three worries: price, damage and whether it is really needed. Prepare an answer for each and keep it factual.

  • It costs a lot more than the cable: Yes, because it cleans the whole pipe instead of opening a path. If the line has backed up more than once this year, the repeat visits usually cost more than doing it properly once.
  • Will it break my pipe: Not pipe that looks sound on camera, which is why we inspect first. Where the camera shows a weak section, I will tell you and recommend a repair instead.
  • Do I really need it: If this is the first clog in years, probably not; the cable is fine. If it keeps coming back and the camera shows buildup, jetting deals with the cause.
  • Can I think about it: Of course. Here is the written price and the video, and the price stays good for the period shown.

Never jet a line you would not stand behind. A tech who recommends a repair instead of an easy jetting ticket is building the kind of trust that brings the repair job back to you.

Building the jetting price

Jetting takes more set-up, more water and more operator time than a cable call, and the machine itself carries financing, maintenance and replacement cost. Labor has also climbed: average hourly earnings at plumbing, heating and AC contractors reached $42.38 in September 2026[3], and benefits add roughly 30% of total compensation on top of wages across private industry[4].

Components of a hydro jetting price. Measure from your own job records.
Cost componentHow to measure itWhere it goes in the price
Set-up and teardownMedian minutes from arrival to first spray and from last spray to departureFixed base for every jetting job
Jetting timeMedian minutes per 50 feet by line typeLine-length bands or hourly rate
Camera before and afterMedian minutes per inspection plus video handlingIncluded in the jetting package
Machine costAnnual finance, maintenance and replacement reserve divided by jetting hoursEquipment charge per job or per hour
Water and disposalWater source, any disposal or vacuum truck costPass-through or fixed allowance
Second technicianJobs where safety or access needs two peopleNamed add-on

Example (fictional): a shop's residential jetting package covers set-up, a camera pass before and after, and jetting up to 100 feet. Median time is 2.5 hours. At a loaded labor cost of $90 an hour and a 2.0 labor multiplier, labor is $450. The machine reserve works out to $85 per job and supplies to $20, giving a package price of about $555, rounded to $575. Each extra 50 feet adds a set amount.

Two structures work. Residential jobs suit line-length bands with a fixed package price, because homeowners want a number before they agree. Commercial kitchens and facilities suit an hourly rate with a minimum, or a maintenance contract with a set number of visits a year.

Commercial grease lines and maintenance contracts

Restaurant and multifamily grease lines are where jetting earns repeat revenue. Instead of waiting for the emergency, offer a schedule based on what the camera shows. A kitchen line that needs jetting every quarter is a predictable account, and predictable accounts are easier to staff than midnight calls.

  1. Inspect and jet once, recording the condition of the line.
  2. Propose a visit frequency based on how fast the grease returns, and review it after the first two visits.
  3. Price the contract per visit with an after-hours option for kitchens that cannot close during service.
  4. Include the camera report with each visit so the manager can show it to the owner or landlord.

For pricing structures across commercial accounts, including not-to-exceed amounts and payment terms, see pricing commercial plumbing service work.

Training techs to offer it at the right moments

Jetting sales usually fail for a simple reason: techs do not raise it, because they fear sounding pushy or are not confident explaining it. Fix that with clear triggers and practice rather than sales targets.

  1. Trigger list: second visit to the same line within a year, heavy grease on the cable head, scale visible on camera, or a commercial kitchen line.
  2. Role play: each tech practices the camera walkthrough and the five-sentence explanation with a manager before offering it to customers.
  3. Ride-alongs: new techs watch an experienced operator run a jetting job from set-up to after video.
  4. Review: managers watch a sample of before and after videos each month and give feedback on both the diagnosis and the explanation.

Track the offer rate, not just the close rate. If techs offer jetting on every trigger and customers still decline, the price or the explanation needs work; if they rarely offer it, the training does.

Paperwork that protects the job

  • A signed acknowledgment when the camera shows pipe at risk and the customer still chooses to jet.
  • Before and after videos saved to the job record with distances noted.
  • A clear statement of what the price includes: length, access points, camera passes and cleanup.
  • Any guarantee in writing, with exclusions for damaged pipe, roots that return and grease from new sources.
  • A follow-up date in your system for maintenance customers, so the next visit is booked before the next clog.

Frequently asked questions

Can hydro jetting damage pipes?

It can make existing damage worse in broken, offset or badly deteriorated pipe. That is why a camera inspection comes first and why you should not jet a line the camera shows is failing.

Should jetting always include a camera inspection?

Yes for main lines. The before video confirms jetting is safe and the after video proves the result, which reduces disputes and repeat calls.

How do I price jetting for restaurants?

Use an hourly rate with a minimum for one-off calls, or a per-visit maintenance contract with a schedule set from the camera findings and an after-hours option.

What if the customer only wants the cable today?

Clear the line, show the video, leave a written jetting price that stays valid for a set period, and schedule a follow-up call.

References

  1. U.S. Environmental Protection Agency (2012). Controlling Fats, Oils, and Grease Discharges from Food Service Establishments (EPA-833-F-12-003) (opens in a new tab) โ†‘

  2. Insurance Information Institute (2019-2023). Facts + Statistics: Homeowners and renters insurance (opens in a new tab) โ†‘

  3. U.S. Bureau of Labor Statistics, Current Employment Statistics (2026). Average hourly earnings of all employees, plumbing, heating, and air-conditioning contractors, not seasonally adjusted (CEU2023822003) (opens in a new tab) โ†‘

  4. U.S. Bureau of Labor Statistics (2026). Employer Costs for Employee Compensation - June 2026 (opens in a new tab) โ†‘

Book a demo

See Ava handle your calls.

Book a short demo. Weโ€™ll walk through your calls and workflow, and agree what Ava should take care of.

Book a demo