Key takeaways
- Open with three questions: every tap or one, hot and cold or only hot, city water or a well.
- Neighbors without water usually means the utility, which handles roughly 240,000 main breaks a year[1]; no truck needed.
- Every frozen-line caller should end the call knowing where the main shutoff is, because the pipe may leak as it thaws.
- Ask why a closed valve was closed before anyone reopens it.
- On a well, write the power status, breaker, gauge reading and pump sounds on the ticket for the technician.
Four reasons the taps go dry
A caller with no water at all needs one of four things: a utility crew, a few hours and some gentle heat, a quarter turn of a valve, or a pump technician. Only some of those need a plumber's truck, and fewer still need it tonight. The person on the phone can usually tell which in about three minutes. Those three minutes are worth more than any other part of the call, because an unnecessary trip at 9 pm costs a technician's evening and costs the customer a fee for a problem you were never going to fix.
All four causes are common. US drinking water systems see approximately 240,000 water main breaks a year[1], and each one leaves a street of customers with dry taps, some of whom ring a plumber before they ring the water company. At the other end of the pipe, around 15% of the US population, over 43 million people, rely on private wells, and more than 23 million households get their drinking water that way[2]. In those homes the city has nothing to do with it: no water means power, the pressure system or the pump.
- Rely on private wells 15%
Source: U.S. Environmental Protection Agency, 2026[2]
Show the data
| Item | Value |
|---|---|
| Rely on private wells | 15% |
What follows is the call itself: three opening questions that split it, four branches with the questions and advice for each, the urgent overrides, a decision card, and what to write on the ticket so the technician who does go knows what they are walking into.
The three questions that split the call
Ask these first, in this order, and write the answers down in the caller's words.
- “Is it every tap in the house, or just one or two?” One fixture with no water is a fixture problem: a closed stop valve, a clogged aerator or cartridge, or one frozen branch line. Unless something is leaking, it is a routine booking.
- “Is it both hot and cold, or only hot?” Hot only is a water heater call with its own questions, covered in handling no-hot-water calls at night.
- “Do you get water from the city, or from a well?” Most well owners answer instantly. If the caller hesitates, ask whether they pay a water bill. No water bill usually means a well.
Then one more question, depending on the answer. For city water: “Do your neighbors have water?” For a well: “Is your power on, and is anything else in the house not working?” Those answers send the call down one of four branches. Keep the order fixed. CSRs who skip to “where is your main?” on every no-water call end up walking callers to valves that were never the problem.
Branch A: the problem is in the street
When the neighbors are dry too, the fix belongs to the water utility. Other signs point the same way: crews or water running in the road, a notice on the door, water that stopped mid-afternoon rather than overnight in a freeze, or several callers from the same few blocks within minutes of each other. When a main breaks near your service area, the second and third calls are the giveaway.
Two quieter versions of this branch catch offices out. A new owner or tenant who has just moved in may find that service was never switched to their name. A home behind on its water bill may have been shut off at the meter. Ask gently: “Have you just moved in, or has the water company been out to the house recently?” Nobody needs to say the word bill.
Example script: “It sounds like the whole street may be affected, which usually means the water company is working on a main. Their outage line or website will tell you when it should be back on. We can't repair anything on the city side, and I don't want you paying for a visit that can't fix it. If the water comes back cloudy, sputtering or with low pressure in just your house, call us back and we'll take a look.”
Keep one line on the triage card with the outage phone number and web page for every water system you serve, so nobody has to search for them at night. When service returns, air in the lines and discolored water are common, and the utility may issue a boil notice; what to tell customers about boil water notices covers that conversation. Log these calls as utility issues rather than lost leads. A share of them come back as real work a week later, when the water is back but the pressure in one house is not.
Branch B: a frozen supply line
A no-water call on the first morning after a hard freeze is a frozen pipe until proven otherwise. Pipes freeze most often where they meet severe cold: hose bibs and sprinkler lines, supply pipes in unheated basements, crawl spaces, attics, garages and kitchen cabinets, and pipes against uninsulated outside walls[3]. The questions narrow down where.
- “Did it stop overnight, or during the day?” Overnight in a cold snap points to freezing.
- “Is any tap giving even a trickle?” A trickle at one fixture and nothing at another narrows it to a branch line.
- “Can you see any pipe that is split, bulging or covered in frost?” A split pipe moves the call straight to the leak branch.
- “Is any part of the house unheated: a crawl space, garage, addition or a room you keep closed off?”
- “Do you know where your main shutoff is?” They need to know before the pipe thaws.
That last question matters most. A frozen pipe that has split starts leaking the moment it thaws, and water damage and freezing claims averaged $15,400 per homeowners claim over 2019 to 2023[4]. Every caller with a frozen line should end the call knowing where the main is and how to close it; walking callers through a water shutoff has the script. If a pipe has already split and water is running, switch to the burst pipe triage rules.
For a frozen line with no leak, the caller can open the faucet it feeds so melting water has somewhere to go, turn up the heat and open cabinet doors under sinks on outside walls. Tell them to warm the pipe gently, with a hair dryer or warm towels, and never with an open flame or a torch. If the house will be empty during the cold, the Red Cross advice is to leave the heat on at no lower than 55°F[3]. A frozen meter, or a service line frozen underground between the street and the house, is a different case: in many towns the meter belongs to the utility, so the caller should ring them first and call you back if the problem is on the house side.
Branch C: a valve somebody closed
The cheapest no-water call to solve is the one where somebody turned the water off. It happens more often than offices expect: a handyman closed the main to change a faucet and left it half shut, a seller closed it before a closing, a landlord shut it during a leak and told nobody, or a whole-house filter or softener was put into bypass the wrong way.
- “Has anyone done plumbing work, or had the water turned off, in the last few days?”
- “Do you have a water softener or a filter where the water comes into the house?” A clogged cartridge or a softener stuck mid-cycle can cut flow to almost nothing.
- “Can you find the main valve and tell me which way the handle points?” A lever across the pipe is closed; a lever in line with it is open. A round wheel turned fully clockwise is closed.
- “Has there been a leak anywhere in the house recently?”
Ask why it was closed before anyone opens it. A main that was shut because of a leak will reopen that leak. If the caller doesn't know why it is off, have them open it a little, then look and listen for running water for a full minute before opening it the rest of the way.
If the valve is open, the softener is in service and flow is still poor at every tap, the next suspect on a city system is a failed pressure-reducing valve. In most homes that is a booked repair, not a midnight emergency. Note the building type as well. In apartments and condos the shutoff for a unit may sit in a hallway closet or a utility room only the building can open, so the call may belong to the property manager first.
Branch D: a well that stopped pumping
In a well home there is no water company to call. Private well water is not regulated by the federal government under the Safe Drinking Water Act, and private well owners are responsible for delivering safe water to their households[2]. USGS notes that homes outside public supply service areas use self-supplied water, typically from a private well[5]. When those taps stop, the cause is nearly always power, the pressure system or the pump.
- “Is your power on? Is anything else in the house off?” No power means no pump; on storm nights use the power outage, well pump and sump call playbook.
- “Has the breaker for the well pump tripped?” One reset is reasonable for a caller to try. If it trips again, stop and book; never coach anyone to work inside a panel.
- “Is there a pressure gauge near the tank, and what does it read?” A reading near zero with the power on points to the pump or the pressure switch.
- “Do you hear the pump running, clicking on and off, or nothing at all?”
- “Was there a storm or lightning recently, or has the water been sputtering or full of air?”
Write the gauge reading and the sounds on the ticket word for word. A technician who knows the pump hums but the gauge sits at zero packs differently from one told only that there is no water. Ask whether there is a generator and where it is running, because generator safety comes before any talk about the pump. If wells make up a large share of your area, adding well pump services covers what that line of work takes.
When no water jumps the queue
Once the cause is clear, most no-water calls can wait for a morning slot. A few should jump the queue whatever the branch: a home with an infant, someone on water-dependent medical care at home, or an elderly or disabled person living alone; a business that cannot open without water, such as a restaurant or a care home; and any no-water call in deep cold where the heating relies on water or the house is empty and freezing. Plumbers are often on call for emergencies, which is why evening and weekend work is common in the trade[6]. Those hours are worth protecting by keeping the calls that can wait off the on-call phone.
| What the caller tells you | Likely cause | What the CSR does | Send a truck? |
|---|---|---|---|
| Neighbors are out too, crews in the street | Utility main break or planned work | Gives the utility's outage number and explains why a visit would not help | No |
| Just moved in, or the water company was out | Service not started, or shut at the meter | Refers to the utility; offers help once service is on | No |
| Stopped overnight in a freeze, one tap trickles | Frozen supply line | Confirms shutoff location, gives gentle-heat advice, books a thaw visit | Booked; sooner if someone vulnerable is home |
| Frozen line plus a split pipe or running water | Burst pipe | Shutoff now, then burst-pipe triage | Yes, by priority |
| Recent work, main closed or half closed | Valve left closed | Asks why it was closed, then guides a slow reopen | Usually no |
| Filter or softener at the entry, weak flow everywhere | Clogged cartridge, bypass or failed pressure valve | Checks the bypass position; books if nothing changes | Booked |
| Well home, power on, gauge near zero | Pump, pressure switch or wiring | Records gauge and sounds; one breaker reset only | Yes, same day where possible |
The same questions on a forwarded line
- Caller
- SI Employee
- Your team
01Caller
Caller reports no water
Rings the business number at 9:40 pm; the line forwards after hours.
02SI Employee
Asks scope and source
Every tap or one? Hot and cold? City water or a well?
03SI Employee
Asks the branch questions
Neighbors, overnight freeze, recent work, power and the pressure gauge.
04SI Employee
Reads back the job
Address, ZIP, callback number and what the caller already checked.
05Your team
On-call tech or morning
Urgent jobs follow the approved on-call path; the rest wait for the office.
Example flow. The questions and the urgent rules are the ones the business approves.
The card works whoever answers. If an SI Employee covers your nights and overflow, give it these questions and your urgent rules: it asks them in order, reads the job back, follows your on-call path for the urgent ones and emails a summary for the rest, so the morning dispatcher starts with the branch already chosen (see what it does). The residential emergency-call example models how an eight-truck company would wake its on-call technician only for the calls that need one.
What the technician needs on the ticket
- The branch and the reason in one line, such as “Well home, power on, gauge at zero, pump hums.”
- When the water stopped, and the outside temperature at the time.
- Everything the caller already tried: breaker reset, valve checked, softener bypassed.
- Where the main shutoff and any crawl space access are, and whether they can be reached.
- Anyone in the home who makes it urgent, plus pets, gate codes and parking.
- City water or well, saved to the customer record so the next call starts one question shorter.
The last item pays back every winter. Records that say well or city, and where the main is, turn a three-minute triage into a one-minute one. If your call intake checklist has no field for water source, add one.
Example: three calls before 8 am
Example: on a January morning after a night well below freezing, a fictional three-truck shop takes three no-water calls between 7:05 and 7:40. The first caller says the house next door has no water either and a utility truck is parked at the corner. The CSR gives her the water company's outage line, says the office will look at it if the pressure is wrong once service returns, and logs it as a utility call.
The second caller's kitchen tap is dry but the bathroom works. The kitchen sink sits on an outside wall above a crawl space. The CSR confirms nothing is dripping, walks him to the main in the basement so he knows where it is, suggests opening the cabinet doors and warming the wall with a hair dryer, and books a 10 am visit in case the line has split. The third caller is on a well. The power is on, the breaker has not tripped, the gauge reads zero and the pump hums. That job goes to the first truck out.
In this example, three no-water calls produce one immediate dispatch, one booked visit and one referral. Without the questions, the shop would have sent three trucks, one of them to a street the city was already digging up.
Train the card before the first freeze
Print the card
One page: the three opening questions, the four branches, the urgent overrides and the outage numbers for every water system you serve.
Flag well homes
Add a water-source field to customer records and fill it in as calls come in.
Role-play each branch
Run one call per branch with every CSR and whoever covers the on-call phone, including a caller who already reopened a valve that was closed for a leak.
Review after each cold snap
Pull every no-water call, check which branch it went to and whether a truck went out that did not need to.
If one branch keeps producing wasted trips, rewrite its questions. If it keeps missing real emergencies, change the urgent rules. Then fold the card into your wider emergency triage questions so the team works from one card, not two.
Frequently asked questions
Should we charge a trip fee if the problem turns out to be the city?
Say your policy before anyone drives out. Good triage means you rarely face the question: if the neighbors are dry or crews are in the street, the call goes to the utility and no truck goes. If the caller still wants a visit, explain the fee and that the technician cannot repair the utility's side.
How can a caller safely thaw a frozen pipe?
Open the faucet the pipe feeds, warm the pipe gently with a hair dryer or warm towels and keep the house heated, never using an open flame. Pipes in crawl spaces, attics, garages, cabinets and against outside walls freeze most often[3]. Make sure the caller knows where the main shutoff is before anything thaws.
How do we know whether a home is on a well?
Ask whether they pay a water bill, and save the answer to the customer record. More than 23 million US households rely on private wells[2], so in rural service areas expect it often.
The water came back after a main break but it is brown and sputtering. Is that a plumbing problem?
Usually not at first. Air and sediment are common after a repair; suggest running a cold tap for a few minutes and checking the utility's notices for a boil advisory. If one house still has low pressure or discolored water after the neighbors are back to normal, book a visit.
Who goes first when several no-water calls come in at once?
Active leaks first, then homes with vulnerable occupants or no heat, then well homes with the power on and no water, then frozen lines with no leak. Utility outages do not take a truck at all.
References
American Society of Civil Engineers (2025). 2025 Report Card for America's Infrastructure: Drinking Water (opens in a new tab) ↑
U.S. Environmental Protection Agency (2026). Private Drinking Water Wells (opens in a new tab) ↑
American Red Cross (2026). Frozen Pipes (opens in a new tab) ↑
Insurance Information Institute (2019-2023). Facts + Statistics: Homeowners and renters insurance (opens in a new tab) ↑
U.S. Geological Survey (2025). Domestic Water Use (opens in a new tab) ↑
U.S. Bureau of Labor Statistics (2025). Occupational Outlook Handbook: Plumbers, Pipefitters, and Steamfitters (opens in a new tab) ↑