Dispatch scheduling

Cutting drive time between plumbing jobs

Cut drive time between plumbing jobs with service zones, job clustering and smarter booking, and decide when route optimization software is worth it.

AssistCall research teamPublished Reviewed by Faruque Amin, VP of Sales and Marketing7 min read

On this page
  1. Why drive time deserves attention
  2. Put a price on an hour of driving
  3. Measure your drive time first
  4. Set service zones
  5. Cluster jobs when booking
  6. Sequence the day
  7. Fewer trips per job
  8. Bring the techs with you
  9. When routing software is worth it
  10. Example: zones before software
  11. Track the results
  12. Frequently asked questions
  13. References
Dispatch scheduling: Cutting drive time between plumbing jobsArticle coverDISPATCH SCHEDULINGCutting drive timebetween plumbing jobsAva for PlumbersInsightsDispatch scheduling: Cutting drive time between plumbing jobsArticle coverDISPATCH SCHEDULINGCutting drive timebetween plumbing jobsAva for Plumbers

Key takeaways

  • Drive time is paid time. Average hourly earnings at plumbing, heating and AC contractors rose from $39.30 in January 2025 to $42.65 in August 2026[1], before benefits and vehicle costs.
  • Measure first: drive minutes per job and per tech day, from your field-service or vehicle data, for a normal month.
  • Most of the saving comes from booking: zones, zone days and offering customers slots when a truck is already nearby.
  • Routing software pays off when you run enough trucks and stops per day that a dispatcher cannot sequence them well by hand; below that, zone rules do most of the work.

Why drive time deserves attention

Plumbers travel to worksites every day[2], and in most shops nobody measures how much of the day goes to driving. It hides in the schedule as the gap between jobs. But every minute in the truck is paid, uses fuel and wears the vehicle, and none of it is billable at full value. Cutting it frees time for one more job a day per tech, or for finishing on time instead of on overtime.

The good news is that most of the gain does not need new technology. It comes from how jobs are booked and assigned, which is something a shop can change next week.

Put a price on an hour of driving

Three numbers give a fair cost. Average hourly earnings for all employees at plumbing, heating and air-conditioning contractors were $42.38 in September 2026[1]. Benefits made up 30.0% of private-industry employer compensation costs in June 2026[3], so the full labor cost of an hour is noticeably higher than the wage. The IRS business standard mileage rate, a common stand-in for vehicle cost, is 76 cents a mile from July 1, 2026[4].

Hourly earnings at plumbing, heating and AC contractorsAverage hourly earnings of all employees. September 2026 is preliminary.
Hourly earnings at plumbing, heating and AC contractorsLine chart. Jan 2025: $39.3; Sep 2025: $40.59; Aug 2026: $42.65; Sep 2026: $42.38.$38$39$40$41$42$43Jan 2025Sep 2025Aug 2026Sep 2026Jan 2025: $39.3Sep 2025: $40.59Aug 2026: $42.65Sep 2026: $42.38$42.38$39.3Hourly earnings at plumbing, heating and AC contractorsLine chart. Jan 2025: $39.3; Sep 2025: $40.59; Aug 2026: $42.65; Sep 2026: $42.38.$38$39$40$41$42$43Jan 2025Sep 2026Jan 2025: $39.3Sep 2025: $40.59Aug 2026: $42.65Sep 2026: $42.38$42.38$39.3

Source: U.S. Bureau of Labor Statistics, Current Employment Statistics, 2026[1]

Show the data
MonthAverage hourly earnings (USD)
Jan 2025$39.3
Sep 2025$40.59
Aug 2026$42.65
Sep 2026$42.38

Example: a fictional tech drives 25 miles and 70 minutes between jobs on an average day. At 76 cents a mile, the vehicle cost is about 19 dollars. If the tech's wage is 40 dollars an hour, the 70 minutes cost about 47 dollars in wages, or about 67 dollars once benefits are added at 30% of total compensation. That is roughly 86 dollars a day per tech, before counting the billable work that could have filled the time. For a crew of six over 250 working days, a 20% cut in drive time is worth around 26,000 dollars a year in direct cost alone.

Measure your drive time first

  1. Pick a normal month

    Avoid freeze weeks and holiday periods, which distort routes.

  2. Pull the data

    Use job start and end times from the field-service system, plus vehicle GPS or mileage logs if you have them.

  3. Calculate per tech

    Drive minutes per day and per job, for each tech, and the share of the working day spent driving.

  4. Map the jobs

    Plot a week of jobs by tech on a map. Criss-crossing lines show where booking, not routing, is the problem.

  5. Set a target

    Choose a realistic target, such as reducing average drive minutes per job by a fifth over a quarter, and review monthly.

Set service zones

Divide your area into three to six zones, using natural boundaries such as highways and rivers rather than drawing circles. Assign techs a home zone based on where they live and their skills, so the first job of the day is close to home and the last job ends near it. The dispatcher still crosses zones when needed, but the default is to stay inside.

  • Keep each zone small enough to cross in about twenty to thirty minutes at normal traffic.
  • Give each zone at least one tech who can handle drains and one who can handle water heaters.
  • Review zone boundaries twice a year as your customer base shifts.
  • Put the zone on every job card so the dispatcher sees it when booking.

The full method for drawing zones is in zone-based scheduling for a service area.

Cluster jobs when booking

The biggest lever is the moment the job is booked. A call-taker who offers the first open slot anywhere creates criss-crossing routes. One who offers slots when a truck is already nearby builds clusters.

  • Show the call-taker which techs are in or near the caller's zone on each day.
  • Offer routine jobs on the days a truck is already in that area: โ€œWe have a plumber in your neighborhood Tuesday morning and Thursday afternoon.โ€
  • Run zone days for maintenance and estimates, so planned work in the far zones is grouped.
  • Keep emergency reserves spread across zones so urgent jobs do not pull a tech across town.

Customers rarely mind being offered two good options. Most will take one of them, and the route gets better without anyone driving faster.

Sequence the day

  • Start each tech's day with a job near home, ideally a fixed first call.
  • Order jobs so the route flows in one direction, not back and forth.
  • Put supplier stops on the way, not as separate trips; stock trucks well enough that most days need none.
  • Leave long, uncertain jobs for the end of a sequence, so an overrun does not push everything else.
  • Re-sequence at midday if a job overruns or an emergency is added.

Sequencing is where a good dispatcher earns their keep, and it is also where habits creep in. Look at one tech's planned route each morning on a map before it is sent. If the line doubles back on itself, ask why. Often the answer is a customer who insisted on a time, which is fine; sometimes it is simply the order the jobs were booked in, which is the fixable kind of drive time.

Fewer trips per job

The cheapest mile is the one never driven. Return visits, parts runs and second trips to quote work all add drive time that no route can remove. Three habits cut them.

  • Ask for photos when booking. A picture of the water heater label or the leaking fitting tells the tech which parts to bring; see capturing job photos before the visit.
  • Stock trucks for the jobs each tech is most often sent to, and restock at the end of the day rather than the start.
  • Give techs the authority to quote and sell common follow-up work on the spot, so a second trip to estimate is not needed.

Track return visits per hundred jobs alongside drive minutes. A shop that halves its return visits often saves more driving than one that buys routing software.

Bring the techs with you

Techs know the roads, the shortcuts and the customers who are always late to open the door. Ask them where the routes go wrong before changing anything, and share the drive-time numbers with them each month. Home zones that respect where people live are popular; zone rules imposed without discussion are often quietly ignored. When a tech suggests a better sequence for their own day, let them use it and see whether the numbers improve.

When routing software is worth it

When zone rules are enough and when route optimization software is worth testing.
Shop situationUsually enoughConsider software when
One to three trucks, mostly localZones and booking rulesRarely needed
Four to ten trucks, mixed job typesZones plus a dispatcher who sequences dailyDaily re-sequencing takes the dispatcher more than an hour, or drive time stays high after zoning
Ten or more trucks, wide areaZones are still the baseUsually worth testing; manual sequencing cannot keep up with changes
Heavy emergency shareReserves spread across zonesSoftware that re-optimizes live when emergencies arrive

Before buying, test any routing tool on a month of your real jobs. Check whether it handles arrival windows, skill matching and emergency insertions, not only distance. A tool that gives the shortest route but ignores the windows you promised will create more phone calls than it saves miles.

Example: zones before software

Example: a fictional six-tech shop measures an average of 38 drive minutes per job. It sets four zones, assigns home zones by where techs live and trains call-takers to offer slots when a truck is nearby. Three months later, the average is 29 minutes per job and most techs fit in an extra job on two or three days a week. The owner decides software can wait until the shop grows.

Track the results

  • Drive minutes per job and per tech day, monthly.
  • Jobs per tech per day.
  • Share of jobs inside the promised arrival window.
  • Overtime hours.

Plumbing, heating and AC contractors generated about $260,000 in receipts per employee in 2022[5]. Even a modest increase in billable time per tech moves that number. Pair drive-time work with two-hour vs four-hour arrival windows and matching technicians to jobs, since the best route is useless if the wrong tech is driving it.

Frequently asked questions

How can a plumbing company reduce drive time?

Set service zones, assign techs home zones, offer customers slots when a truck is already nearby, sequence each day in one direction and re-sequence at midday when plans change.

How much does drive time cost a plumbing business?

Add the paid labor time with benefits to vehicle cost per mile. Using current average hourly earnings, a typical benefits load and the IRS mileage rate, an hour of driving per tech per day adds up to a large annual cost across a crew.

Is route optimization software worth it for a small plumbing shop?

Often not for one to three trucks; zones and booking rules do most of the work. It becomes worth testing as truck counts rise and manual sequencing takes the dispatcher too long.

What should I check before buying routing software?

Test it on a month of your real jobs and check that it respects arrival windows, skill requirements and emergency insertions, not only distance.

References

  1. U.S. Bureau of Labor Statistics, Current Employment Statistics (2026). Average hourly earnings of all employees, plumbing, heating, and air-conditioning contractors, not seasonally adjusted (CEU2023822003) (opens in a new tab) โ†‘

  2. U.S. Bureau of Labor Statistics (2025). Occupational Outlook Handbook: Plumbers, Pipefitters, and Steamfitters (opens in a new tab) โ†‘

  3. U.S. Bureau of Labor Statistics (2026). Employer Costs for Employee Compensation - June 2026 (opens in a new tab) โ†‘

  4. Internal Revenue Service (2026). Standard mileage rates (opens in a new tab) โ†‘

  5. U.S. Census Bureau (2022). Statistics of U.S. Businesses 2022: U.S. and states, 6-digit NAICS (opens in a new tab) โ†‘

Book a demo

See Ava handle your calls.

Book a short demo. Weโ€™ll walk through your calls and workflow, and agree what Ava should take care of.

Book a demo