Dispatch scheduling

Estimating plumbing job durations for better scheduling

Build time standards from your own job history: pick the right percentile, adjust for tech level and old homes, and keep the board on time.

AssistCall research teamPublished Reviewed by Faruque Amin, VP of Sales and Marketing7 min read

On this page
  1. Why gut-feel durations break the afternoon
  2. The data you need first
  3. Method: build the standard from percentiles
  4. Adjust for the tech, not for every job
  5. What a wrong standard costs
  6. Example: fixing the drain standard
  7. Using standards on the board and in the script
  8. Mistakes that make standards useless
  9. Keep standards current
  10. Frequently asked questions
  11. References
Dispatch scheduling: Estimating plumbing job durations for better schedulingArticle coverDISPATCH SCHEDULINGEstimating plumbing jobdurations for betterschedulingAva for PlumbersInsightsDispatch scheduling: Estimating plumbing job durations for better schedulingArticle coverDISPATCH SCHEDULINGEstimating plumbingjob durations forbetter schedulingAva for Plumbers

Key takeaways

  • Use your completed-job history, not memory, to set a time standard per job type.
  • Book the 80th percentile for routine work and keep the median for reporting; the gap is your buffer.
  • Adjust for tech experience and house age instead of padding every job.
  • Review standards monthly; a stale standard is the most common cause of late afternoon arrivals.

Why gut-feel durations break the afternoon

Most boards run on durations someone guessed years ago: an hour for a faucet, two for a water heater, ninety minutes for a drain. Those guesses are usually close on average and wrong on any given day, and the error piles up. If each morning job runs fifteen minutes over, the 2 p.m. customer is waiting an hour by the time the tech arrives.

Good time standards do three jobs. They tell the CSR how many slots really exist, they tell dispatch when to warn a customer, and they show the owner which job types quietly lose money because they take longer than the price assumes.

The data you need first

You need a few months of completed jobs with clean timestamps. Most field service apps record these when techs tap the job status buttons; if yours do not, fix the habit before you build anything.

  • Job type, using a short fixed list rather than free text (for example: drain, toilet, faucet, water heater replace, leak locate, sewer camera, fixture install).
  • On-site time, from arrived to completed. Keep drive time separate so routing problems do not hide inside job durations.
  • Tech name and level (apprentice, journeyman, lead).
  • Year the home was built, when known, and whether it was a crawl space, slab or basement job.
  • Whether the job needed a second visit, so you can exclude return trips from the first-visit standard.

Throw out obvious errors before you calculate: jobs closed hours after the tech left, or zero-minute jobs where someone tapped two buttons at once. Leave in the slow jobs that were real; they are the reason you are doing this.

Method: build the standard from percentiles

  1. Group by job type

    Pull on-site minutes for each job type. Twenty or more completed jobs per type is a workable minimum; below that, borrow the standard of the closest similar job and mark it provisional.

  2. Find the median and the 80th percentile

    The median (P50) is the typical job. The 80th percentile (P80) is the time that four in five jobs finish within. A spreadsheet PERCENTILE function does this in seconds.

  3. Book at P80, report at P50

    Put P80 on the board for routine work so most jobs finish inside their slot. Use P50 to judge tech performance, so nobody is measured against a padded number.

  4. Round to your slot size

    If your board works in 30-minute blocks, round P80 up to the next block. Mixed rounding makes the schedule harder to read than the minutes it saves.

  5. Mark long-tail types

    Where P80 is more than double the median (leak locates and older-home drain work often are), book a diagnostic slot first and schedule the repair after.

Example: time standards from a fictional shop's last six months of completed jobs
Job typeMedian on-site80th percentileBooked slot
Toilet repair or rebuild50 min75 min1.5 h
Faucet replace65 min95 min2 h
Main line drain clear70 min115 min2 h
Tank water heater replace (like for like)2 h 40 min3 h 50 min4 h
Leak locate90 min3 h 10 minDiagnostic 2 h, repair rebooked
Sewer camera inspection45 min70 min1.5 h

Adjust for the tech, not for every job

Padding every job wastes capacity. A better approach is a small set of multipliers applied only when they apply. Skill is the biggest one. Plumbers typically learn through a 4- or 5-year apprenticeship[1], and apprentices usually log about 2,000 hours of paid on-the-job training a year[1], so a second-year apprentice and a 15-year lead are not interchangeable on a water heater swap.

Pay data shows how wide the skill range is. O*NET reports hourly wages for US plumbers from $21.22 at the 10th percentile to $52.13 at the 90th, with a $30.67 median[2]. The market prices experience steeply, and so should your time standards.

Hourly pay spread for US plumbersBLS wage data as published by O*NET, 2025.
Hourly pay spread for US plumbersColumn chart. Lowest 10%: $21.22; Median: $30.67; Highest 10%: $52.13.$0$20$40$60Lowest 10%: $21.22$21.22Lowest 10%Median: $30.67$30.67MedianHighest 10%: $52.13$52.13Highest 10%Hourly pay spread for US plumbersColumn chart. Lowest 10%: $21.22; Median: $30.67; Highest 10%: $52.13.$0$20$40$60Lowest 10%: $21.22$21.22Lowest 10%Median: $30.67$30.67MedianHighest 10%: $52.13$52.13Highest 10%

Source: O*NET OnLine (U.S. Department of Labor), BLS 2025 wage data, 2025[2]

Show the data
Pay levelHourly wage (USD)
Lowest 10%$21.22
Median$30.67
Highest 10%$52.13
  • Tech level: apprentice on lead-level work, multiply by about 1.3 until their own history says otherwise.
  • House age: older housing stock hides surprises. EPA notes lead pipes are more likely in older cities and in homes built before 1986[3]; add a buffer when intake shows an older home with original piping.
  • Access: crawl space or finished ceiling, add a fixed block rather than a percentage.
  • First visit to a new customer: allow ten extra minutes for walkthrough and paperwork.

What a wrong standard costs

A standard that is too short costs overtime, late arrivals and rushed work. One that is too long leaves paid hours idle. Either way the cost runs at a loaded rate: private-industry employers paid an average $46.89 per hour worked in total compensation in June 2026, with benefits making up 30.0% of that[4].

The revenue side matters as much. Plumbing, heating and AC contractors generated about $260,000 in receipts per employee in 2022[5]. Each hour of capacity a bad standard hides is an hour that never reaches that number.

$46.89

Average private-industry employer cost per hour worked, wages plus benefits, June 2026[4]

Example: fixing the drain standard

Example (fictional): a shop booked every drain call as one hour. Its job history showed a 70-minute median and a 115-minute 80th percentile for main line clears, and afternoon drain jobs were late more than half the time. Splitting drains into two types fixed most of it: sink and tub drains kept a one-hour slot, while main line clears moved to two hours.

Example, continued: the change appeared to cut capacity by two slots a day. In practice the shop finished more jobs, because techs stopped overrunning into the next booking, and callbacks for rushed main line work fell. The CSR script changed too: 'Is it one drain backing up, or are several fixtures slow?' decides which slot to offer.

Using standards on the board and in the script

A time standard only helps if it shows up where decisions are made. On the dispatch board, each booked job should display its standard and a running clock once the tech marks arrived. When a job passes its median, nothing happens. When it passes the booked slot, the next customer's window is at risk, and dispatch decides whether to send a late message, move a job or pull in the floating truck.

In the CSR script, standards decide which slot to offer. A caller describing a single slow sink gets a short slot; a caller describing gurgling toilets and a basement floor drain backing up gets a main line slot. Two or three triage questions per job type are enough, and they should map directly onto the job types in your standards table. If CSRs keep booking the wrong type, the usual problem is that the questions do not separate the types cleanly, not that the CSR is careless.

Standards also feed capacity. Add up the booked slots for a day, add drive time between stops and compare the total with paid hours. That is the honest number of jobs a tech can hold, and it is usually lower than the number on the sales manager's whiteboard.

Mistakes that make standards useless

  • Using averages. One four-hour disaster drags the mean up and makes every slot too long; percentiles are robust to outliers.
  • Letting techs set their own slot lengths job by job. Standards exist so the board is predictable.
  • Mixing install and service work in one job type. A water heater swap and a water heater repair are different jobs.
  • Keeping the numbers from the techs. Standards that feel secret feel like surveillance.
  • Ignoring return trips. If a job type often needs a second visit, the fix is better intake or truck stock, not a longer first slot.

Keep standards current

  1. Recalculate monthly from the last six months of completed jobs.
  2. Flag any job type whose median moved by more than ten minutes and ask the techs why before you change the slot.
  3. Retire job types nobody uses and split ones with a very wide spread.
  4. Share the standards table with techs. When they see their own data, the conversation moves from blame to fixing the cause.
  5. Feed the standards into zone-based scheduling so zone days hold what they promise.

Standards also make customer updates easier. When dispatch can see that a job is past its P80, it is time to tell the next customer the tech is running late, not twenty minutes after the window closes.

Frequently asked questions

What percentile should I use to book plumbing jobs?

Many shops book routine work at the 80th percentile of their own history and use the median for performance reviews. That keeps most jobs inside their slot without measuring techs against a padded number.

How many past jobs do I need to set a time standard?

About twenty completed jobs per type is a workable start. For rarer jobs, borrow the closest similar standard, mark it provisional and replace it once you have your own data.

Should drive time be part of the job duration?

No. Track it separately. Mixing them hides routing problems inside job times and makes the standards swing with traffic instead of with the work.

How often should time standards be updated?

Recalculate monthly from a rolling six months, and investigate any job type whose median shifts noticeably before you change the booked slot.

References

  1. U.S. Bureau of Labor Statistics (2025). Occupational Outlook Handbook: Plumbers, Pipefitters, and Steamfitters (opens in a new tab) โ†‘

  2. O*NET OnLine (U.S. Department of Labor), BLS 2025 wage data (2025). National Wages 47-2152.00 - Plumbers, Pipefitters, and Steamfitters (opens in a new tab) โ†‘

  3. U.S. Environmental Protection Agency (2026). Basic Information about Lead in Drinking Water (opens in a new tab) โ†‘

  4. U.S. Bureau of Labor Statistics (2026). Employer Costs for Employee Compensation - June 2026 (opens in a new tab) โ†‘

  5. U.S. Census Bureau (2022). Statistics of U.S. Businesses 2022: U.S. and states, 6-digit NAICS (opens in a new tab) โ†‘

Book a demo

See Ava handle your calls.

Book a short demo. Weโ€™ll walk through your calls and workflow, and agree what Ava should take care of.

Book a demo