Key takeaways
- Plumber pay is widely spread, from under $44,150 for the lowest-paid 10% to over $108,420 for the top 10%, so the interview has to place a candidate on that range[1].
- Ask about specific past jobs, not hypotheticals: "Tell me about the last water heater you replaced" beats "How would you replace a water heater?"
- Score every candidate on the same five areas: technical depth, diagnosis, customer handling, safety and reliability.
- Customer handling matters because 82% of US adults at least sometimes read reviews before buying from someone new[2].
- Pair the interview with a hands-on test; talk alone does not show skill.
What the interview has to find out
A plumbing interview has one job: predict how this person will perform alone in a customer's basement at 7 p.m. That means testing four things a resume cannot show: how deep their technical knowledge goes, how they diagnose a problem they have not seen before, how they talk to customers and how seriously they take safety. Specialty trade contractors recorded 2.3 recordable injury and illness cases per 100 full-time workers in 2024, so the safety questions are not a formality[3].
The interview also sets pay. The median plumber earned $63,800 in May 2025, but the lowest-paid 10% earned less than $44,150 and the highest-paid 10% more than $108,420[1]. In hourly terms that is roughly $21.22 to $52.13[4]. Where a candidate lands depends on what they can do without supervision, which is exactly what the questions below are built to find.
A 10-minute phone screen
Screen before you invite anyone to the shop. With 298,000 open construction jobs in September 2026, good candidates have options, so keep it short and respectful of their time[5].
- "What kind of plumbing have you done most in the last two years: service, remodel, new construction or commercial?"
- "What license do you hold, in which state, and when does it renew?"
- "Are you comfortable with on-call rotation? How often have you done it before?"
- "Do you have a valid driver's license, and would your record qualify you to drive a company van?"
- "What pay range are you looking for, and how were you paid at your last job: hourly, commission or flat rate?"
- "When could you start?"
Technical depth: questions and what good sounds like
- "Walk me through the last water heater you replaced, from shutting it off to the customer signing." Good: names the shutoffs, venting or gas checks, expansion tank and code items, permit or inspection if required. Weak: "I just swap it out."
- "What size water line would you run to a house with three bathrooms, and why?" Good: asks about fixture count, pressure and run length before answering. Weak: a single number with no reasoning.
- "Tell me about a drain line you could not clear the first time." Good: describes switching tools or camera inspection and explaining options to the customer. Weak: blames the customer or the pipe.
- "What do you check before you solder or press a fitting?" Good: clean, dry, supported, correct fitting, fire safety. Weak: no mention of fire or water in the line.
Diagnosis under uncertainty
Diagnosis separates a parts swapper from a technician. Ask the candidate to talk through a real case, then add a complication.
- "Customer says the water heater makes noise and runs out of hot water fast. What do you check, in order?" Then: "The tank is eight years old and the customer is on a tight budget. What do you tell them?"
- "A toilet runs every few minutes, and you have already replaced the flapper. What next?" Listen for checking the fill valve, overflow height and supply pressure.
- "You find a leak inside a wall but cannot see the source. How do you decide where to open it?" Good: moisture meter, thermal camera, minimal cuts, telling the customer before cutting.
Tip: give every candidate the same scenario. Comparing five people on one question is fairer and more revealing than five different conversations.
Customer handling
Most of your reviews are written about the technician, not the office. Pew found 82% of US adults at least sometimes read online ratings or reviews before buying something for the first time[2]. Test how the candidate explains, quotes and handles pushback.
- "Explain to me, as if I were the homeowner, why I need a new pressure-reducing valve." Good: plain language, the risk of not fixing it, options. Weak: jargon or pressure tactics.
- "A customer says your price is double what their neighbor paid. What do you say?" Good: stays calm, explains scope, offers options, does not trash competitors.
- "Tell me about a customer who was unhappy with your work. What happened next?" Good: owns the mistake, describes the fix. Weak: never had an unhappy customer.
- "How do you leave a job site?" Good: cleanup, shoe covers, explaining what was done, asking for questions.
Safety and reliability
- "Tell me about a time you stopped a job because something was unsafe." Good: a specific case such as a gas smell, electrical hazard or confined space and who they called.
- "What PPE do you carry on a normal service call?" Listen for eye protection, gloves, knee pads and respiratory protection for dusty or moldy spaces.
- "How do you handle being on call when you have plans?" Good: honest about swaps and communication. Weak: "I always answer" with no detail.
- "What would your last supervisor say is the one thing you need to improve?" A candid answer predicts coachability.
Scoring sheet
| Area | 1 (weak) | 3 (solid) | 5 (strong) |
|---|---|---|---|
| Technical depth | Vague, generic steps | Correct steps, some code awareness | Correct steps, code items, alternatives |
| Diagnosis | Guesses or swaps parts | Logical order of checks | Logical order plus how they confirm the cause |
| Customer handling | Jargon, defensive | Clear, polite | Clear, gives options, handles pushback |
| Safety | No examples | Knows PPE and basics | Has stopped work for a hazard and explains why |
| Reliability | Evasive on schedule or record | Straight answers | Specific examples of covering shifts and communication |
Have two people score independently and compare. If the scores differ by two points or more in an area, discuss the specific answer that caused it. Move candidates who average 3 or higher to a hands-on skills test.
Running the interview
Send the format in advance
Tell the candidate how long it takes, who they will meet and that there is a practical test. It reduces no-shows.
Open with their work history
Five minutes on the jobs they have done most. It relaxes them and tells you where to probe.
Ask the same core questions
Use the questions above in the same order for everyone, with follow-ups based on answers.
Give them time to ask
Strong candidates ask about trucks, on-call, training and how pay works. No questions is a yellow flag.
Score and decide quickly
Score the same day and reply within two business days, even if the answer is no.
Keep questions job-related and avoid anything about age, family plans, religion, national origin or disability. If you hire veterans or people from target groups, make the tax-credit screening part of the offer packet as described in our WOTC guide.
Reference checks that test the interview
A reference call is a second interview with someone who watched the candidate work. Use it to confirm or challenge your lowest score, not to collect compliments. Ask for a former supervisor or lead, not a friend, and keep the questions specific.
- "What kind of calls did you send them on by themselves?" This tells you the real level of independence.
- "How did customers react to them? Did you get callbacks or complaints on their work?"
- "How were they on on-call weeks and early starts?"
- "What did you have to coach them on most?" Compare the answer with the weakness the candidate named.
- "Would you hire them again for the same role?" Listen for hesitation more than the words.
Note the answers on the same scoring sheet. If a reference contradicts the interview on safety or reliability, believe the reference and dig further before making an offer.
Example: two candidates, one opening
Example (fictional): candidate A has ten years of new construction and scores 5 on technical depth but 2 on customer handling. Candidate B has four years of residential service and scores 3 on technical depth and 5 on customer handling. For a service opening, the shop hires B, pairs them with a senior tech for complex installs and offers A a role on its new construction crew instead.
Frequently asked questions
What should I ask a plumber in an interview?
Ask about specific recent jobs: the last water heater they installed, a drain they could not clear, a customer who was unhappy. Add a diagnosis scenario, a customer explanation role-play and safety questions, and score each area on the same scale for every candidate.
How long should a plumber interview take?
About 45 to 60 minutes for the conversation plus a separate practical test. Screen by phone for 10 minutes first.
What are red flags in a plumbing technician interview?
Vague answers about recent work, blaming customers for every problem, no safety examples, evasiveness about driving record or schedule, and no questions about the job.
References
U.S. Bureau of Labor Statistics (2025). Occupational Outlook Handbook: Plumbers, Pipefitters, and Steamfitters (opens in a new tab) โ
Pew Research Center (2016). Online Reviews (Online Shopping and E-Commerce) (opens in a new tab) โ
U.S. Bureau of Labor Statistics (2024). Industries at a Glance: Specialty Trade Contractors (NAICS 238) (opens in a new tab) โ
O*NET OnLine (U.S. Department of Labor), BLS 2025 wage data (2025). National Wages 47-2152.00 - Plumbers, Pipefitters, and Steamfitters (opens in a new tab) โ
U.S. Bureau of Labor Statistics (2026). Job Openings and Labor Turnover Survey, Table 1: Job openings levels and rates by industry (opens in a new tab) โ