Licensing compliance

Silica rules when plumbers cut concrete

OSHA's silica limits, the Table 1 controls for saws, core drills and jackhammers on plumbing jobs, the written plan, housekeeping rules and medical exams.

AssistCall research teamPublished Reviewed by Faruque Amin, VP of Sales and Marketing7 min read

On this page
  1. Why slab work puts plumbers under the silica rule
  2. The limits in plain numbers
  3. Two ways to comply: Table 1 or measure
  4. Table 1 controls for common plumbing tasks
  5. The written exposure control plan
  6. Buying the right tools once
  7. Housekeeping: the rule most crews break
  8. Respirators and medical exams
  9. Example: an under-slab drain repair
  10. Frequently asked questions
  11. References
Licensing compliance: Silica rules when plumbers cut concreteArticle coverLICENSING COMPLIANCESilica rules whenplumbers cut concreteAva for PlumbersInsightsLicensing compliance: Silica rules when plumbers cut concreteArticle coverLICENSING COMPLIANCESilica rules whenplumbers cut concreteAva for Plumbers

Key takeaways

  • OSHA's construction silica limit is 50 micrograms per cubic meter averaged over 8 hours, with an action level of 25.
  • Following Table 1 for a task, such as a wet handheld saw or a shrouded drill, lets you skip air sampling for that task.
  • A handheld saw with water needs no respirator outdoors for up to 4 hours a shift, but needs an APF 10 respirator indoors or beyond 4 hours.
  • Every employer with exposed workers needs a written exposure control plan, a competent person and no dry sweeping or compressed air cleanup.

Why slab work puts plumbers under the silica rule

Concrete, block, brick, mortar and stone all contain crystalline silica. Cutting, drilling, grinding or breaking them creates fine respirable dust that settles deep in the lungs. OSHA says about 2.3 million people in the United States are exposed to silica at work, and links it to silicosis, an incurable lung disease, as well as lung cancer, chronic obstructive pulmonary disease and kidney disease[1].

Plumbers meet silica on under-slab drain repairs, when they saw-cut and break out a trench in a garage or basement floor, core through a foundation for a new service line, or drill block walls for supports. These jobs are short compared with a concrete contractor's, but they are often indoors, in small rooms with poor air movement, which is exactly where exposure builds up fastest. Silica disease also differs from the injuries that fill most safety logs. Specialty trade contractors recorded 2.3 recordable injury and illness cases per 100 full-time workers in 2024[2], mostly cuts, strains and falls that show up the same day. Silicosis can take years to appear, long after the job that caused it, which is why the rule focuses on controlling dust now rather than waiting for symptoms.

2.3 million

people in the US exposed to silica at work, according to OSHA[1]

The limits in plain numbers

The construction standard, 29 CFR 1926.1153, sets a permissible exposure limit of 50 micrograms of respirable crystalline silica per cubic meter of air, calculated as an 8-hour time-weighted average[3]. It also sets an action level of 25 micrograms per cubic meter, which triggers further duties for employers who measure exposure rather than follow Table 1[3].

OSHA construction silica limits, 8-hour average
OSHA construction silica limits, 8-hour averageComparison. Permissible exposure limit: 50 micrograms per cubic meter; Action level: 25 micrograms per cubic meter.50 micrograms per cubic meterPermissible exposure limitPermissible exposure limit: 50 micrograms per cubic meter25 micrograms per cubic meterAction levelAction level: 25 micrograms per cubic meterOSHA construction silica limits, 8-hour averageComparison. Permissible exposure limit: 50 micrograms per cubic meter; Action level: 25 micrograms per cubic meter.50 micrograms per cubic meterPermissible exposure limitPermissible exposure limit: 50 micrograms per cubic meter25 micrograms per cubic meterAction levelAction level: 25 micrograms per cubic meter

Source: Legal Information Institute, Cornell Law School (Code of Federal Regulations), 2026[3]

Show the data
ItemValue
Permissible exposure limit50 micrograms per cubic meter
Action level25 micrograms per cubic meter

Those numbers are tiny. You cannot judge them by eye, and a visible dust cloud is already a sign that exposure is far too high. That is why most small contractors use Table 1 instead of measuring.

Two ways to comply: Table 1 or measure

OSHA gives employers a choice. They can follow the control methods laid out in Table 1 of the construction standard for each listed task, or they can assess workers' exposure and control it to the limit by other means[4]. For a plumbing company, Table 1 is almost always the practical route, because it tells you exactly which tool controls and respirators to use and removes the need for air sampling on those tasks.

The catch is that Table 1 only works if you follow it fully for the task: the right water feed or dust collector, maintained and used as the manufacturer intends, plus the listed respirator where the table requires one. Skip one element and you are back to having to measure and prove exposure.

Table 1 controls for common plumbing tasks

Selected Table 1 entries from 29 CFR 1926.1153 relevant to plumbing work; read the full table for every condition.
TaskRequired controlRespirator, 4 hours or less per shiftRespirator, more than 4 hours
Handheld power saw cutting slab or blockIntegrated water delivery feeding water continuously to the bladeOutdoors: none. Indoors or enclosed: APF 10APF 10 indoors and outdoors
Handheld or stand-mounted drill, including rotary hammerShroud or cowling with dust collection system, operated per manufacturer instructionsNoneNone
Rig-mounted core saw or drillWater delivered to the cutting surfaceNoneNone
Jackhammer or chipping tool breaking slabContinuous stream or spray of water at the point of impactOutdoors: none. Indoors or enclosed: APF 10APF 10 indoors and outdoors

For each of these tasks the controls do the heavy lifting[3]. A wet saw with the water actually running, a drill shroud connected to a vacuum with the right filter, and a jackhammer with a water spray at the bit remove most of the dust before anyone breathes it. The respirator column is the backup, and it is driven by two things you control: whether you work indoors and how long the task runs during the shift.

Most under-slab repairs happen indoors. Plan for an APF 10 respirator, such as a fit-tested half mask with the correct filters, for anyone sawing or breaking concrete inside, even on a short job.

The written exposure control plan

Every employer covered by the standard must establish and implement a written exposure control plan[3]. It does not need to be long. The rule says it must describe the tasks that involve exposure, the engineering controls, work practices and respiratory protection for each task, the housekeeping measures used to limit exposure, and the procedures used to restrict access to work areas when necessary[3].

  1. List your silica tasks

    Walk through a year of jobs and list every time crews cut, drill, core or break concrete, block, brick or stone.

  2. Match each task to Table 1

    Write down the Table 1 entry, the tool and the control your crews use, and the respirator for indoor and longer jobs.

  3. Set housekeeping rules

    State that dust and debris are cleaned with wet methods or HEPA vacuums, never dry sweeping or compressed air.

  4. Restrict access

    Describe how you keep homeowners, pets and other trades away while cutting, such as closing doors and posting a simple sign.

  5. Name the competent person

    Designate who makes frequent and regular inspections of job sites, materials and equipment to put the plan into action.

  6. Review yearly

    Check the plan against new tools and new types of work at least once a year.

Buying the right tools once

Compliance is mostly a purchasing decision. Once the van carries a saw with an integrated water feed, a drill shroud that fits your core and hammer bits, a vacuum with a filter rated for the job and a box of fit-tested respirators, following Table 1 becomes the easy option rather than the slow one. Crews skip controls when the right tool is back at the shop.

  • Standardize on one or two saw and drill models so shrouds and hoses fit every van.
  • Add the dust control kit to the van inventory list that is checked each week.
  • Replace worn shrouds and hoses as soon as they leak; a shroud that does not seal is not a Table 1 control.
  • Keep spare filters and respirator cartridges in stock, not on a reorder list.

Housekeeping: the rule most crews break

The silica standard bans the two cleanup habits most crews fall back on. Employers may not allow dry sweeping or dry brushing where it could contribute to exposure, and may not allow compressed air to be used to clean clothing or surfaces, except in narrow situations such as when the air is used with a system that captures the dust cloud[3]. Wet sweeping and HEPA-filtered vacuuming are the alternatives.

  • Mist the floor before sweeping up slab debris, or use a HEPA vacuum.
  • Bag the broken concrete inside the work area instead of carrying loose pieces through the house.
  • Never blow dust off clothes or tools with an air hose or leaf blower.
  • Keep a dedicated HEPA vacuum on vans that do slab or block work, and change filters as the maker recommends.

Clean cleanup also matters to the customer. Silica dust tracked through a finished basement is the kind of thing that turns into a complaint or a damage claim, even when nobody mentions health.

Respirators and medical exams

When Table 1 or your assessment calls for a respirator, you need a respiratory protection program: medical clearance, fit testing and training on the respirator your crew wears. On top of that, the silica standard requires employers to offer medical surveillance to each employee who will be required to wear a respirator under the standard for 30 or more days a year[3][4].

A small residential plumbing company may never reach that threshold. A company that does regular slab work, commercial core drilling or lead service line work through foundations might. Count respirator days per worker from your job records so you know where you stand.

Example: an under-slab drain repair

Example: a crew is booked to replace a broken cast iron drain under a basement slab. The job requires about two hours of sawing and an hour of breaking concrete, all indoors. Following the company's written plan, the lead tech uses a handheld saw with an integrated water feed and a jackhammer with a water spray at the bit. Because the work is indoors, both workers wear fit-tested half-mask respirators rated APF 10 while cutting and breaking.

The helper lays plastic over the stairs, closes the basement door and asks the homeowner to keep the children upstairs. The slurry is vacuumed with a wet-capable HEPA vacuum, the broken concrete is bagged in the basement, and the tech notes the respirator use on the work order so the company can count respirator days for the year. Nothing about the job is exotic. It simply follows the plan.

Frequently asked questions

Do plumbers have to follow the OSHA silica rule?

Yes, if their workers cut, drill, grind or break materials containing silica, such as concrete, block or brick, in construction work. Most do this through Table 1 controls and a written exposure control plan.

Do I need a respirator to cut a slab with a wet saw?

Under Table 1, a handheld saw with integrated water delivery needs no respirator outdoors for 4 hours or less a shift, but needs an APF 10 respirator indoors or in enclosed areas, and for longer than 4 hours anywhere.

Is a drill with a shroud enough when drilling concrete?

For handheld and stand-mounted drills, including rotary hammers, Table 1 lists a shroud or cowling with a dust collection system and no respirator, provided the tool is operated as the manufacturer instructs.

Can we sweep up concrete dust?

Not dry. The standard bars dry sweeping or brushing where it could contribute to exposure. Use wet methods or a HEPA-filtered vacuum.

References

  1. Occupational Safety and Health Administration (2026). Silica, Crystalline (opens in a new tab) โ†‘

  2. U.S. Bureau of Labor Statistics (2024). Industries at a Glance: Specialty Trade Contractors (NAICS 238) (opens in a new tab) โ†‘

  3. Legal Information Institute, Cornell Law School (Code of Federal Regulations) (2026). 29 CFR 1926.1153 - Respirable crystalline silica (opens in a new tab) โ†‘

  4. Occupational Safety and Health Administration (2026). Silica, Crystalline: Construction (opens in a new tab) โ†‘

Book a demo

See Ava handle your calls.

Book a short demo. Weโ€™ll walk through your calls and workflow, and agree what Ava should take care of.

Book a demo