Growth service lines

Restaurant plumbing: grease traps and FOG rules

How plumbers serve restaurants under municipal FOG programs: traps vs interceptors, service schedules, inspection records, jetting and manager scripts.

AssistCall research teamPublished Reviewed by Faruque Amin, VP of Sales and Marketing7 min read

On this page
  1. Why grease is a plumbing business, not just a pumping one
  2. How municipal FOG programs work
  3. Traps, interceptors and who services what
  4. Installing or replacing an interceptor
  5. Setting a service schedule from measurements
  6. Best practices you can teach kitchen staff
  7. Scheduling around service hours
  8. Growing the restaurant line
  9. Frequently asked questions
  10. References
Growth service lines: Restaurant plumbing: grease traps and FOG rulesArticle coverGROWTH SERVICE LINESRestaurant plumbing:grease traps and FOGrulesAva for PlumbersInsightsGrowth service lines: Restaurant plumbing: grease traps and FOG rulesArticle coverGROWTH SERVICE LINESRestaurant plumbing:grease traps and FOGrulesAva for Plumbers

Key takeaways

  • EPA's report to Congress found grease from restaurants, homes and industry was the most common cause of reported sewer blockages, at 47%[1].
  • Cities enforce FOG rules through pretreatment programs: interceptor requirements, maintenance records, inspections, surcharges and fines.
  • Service frequency depends on how much grease a kitchen produces and how well it follows best practices, so set schedules from measurements, not habit[1].
  • The record is the product: dated service reports with depth readings, photos and hauler manifests are what inspectors ask for.
  • Book restaurant work outside service hours and confirm with the manager by text the day before.

Why grease is a plumbing business, not just a pumping one

Fats, oils and grease (FOG) cool and harden in drain lines, and they do the same in city sewers. EPA's fact sheet on food service discharges quotes its report to Congress on sewer overflows: grease from restaurants, homes and industrial sources is the most common cause of reported blockages, at 47%, because it solidifies, reduces capacity and blocks flow[1]. That is why cities regulate restaurant grease, and why restaurants need more than an occasional pump-out.

Share of reported sewer blockages caused by greaseFrom EPA's 2004 report to Congress on combined and sanitary sewer overflows, as quoted in EPA's 2012 FOG fact sheet.
Share of reported sewer blockages caused by greaseDonut chart. Grease from restaurants, homes and industrial sources: 47%.Grease from restaurants, homes and industrial sources: 47%47%
  • Grease from restaurants, homes and industrial sources 47%

Source: U.S. Environmental Protection Agency, 2012[1]

Show the data
ItemValue
Grease from restaurants, homes and industrial sources47%

The market is large. The National Restaurant Association projects restaurant and foodservice sales of $1.55 trillion in 2026, with industry employment of 15.8 million[2]. Every commercial kitchen needs drain lines that flow, an interceptor that meets local rules and records that survive an inspection. Plumbers who understand the rules can offer the whole package: installation, line cleaning, interceptor maintenance coordination, repairs and the paperwork.

How municipal FOG programs work

Most FOG rules come from the city's or sewer district's pretreatment program, which uses general pretreatment standards and local authority to control what businesses put into the sewer. EPA notes that a growing number of control authorities set numeric limits, require best management practices including interceptors, and impose inspections, periodic grease pumping, penalties and surcharges on restaurant sewer bills[1].

Enforcement can be serious. EPA's fact sheet cites New York City, which found a 73% non-compliance rate with its grease trap ordinance among restaurants and instituted a $1,000-per-day fine for FOG violations[1]. Your local program may be stricter or looser, so read the ordinance and the program's inspection checklist before you advise any restaurant.

  • Find out who runs the program: the city utility, a sewer district or the county.
  • Download the ordinance and the inspection form, and note the required interceptor types, sizing method and maintenance rules.
  • Check whether the program requires a FOG permit, a registered hauler, manifests or online reporting of pump-outs.
  • Ask whether the program keeps a list of approved service providers, and how to get on it.

Traps, interceptors and who services what

Grease control devices in a restaurant and who usually services them
DeviceWhere it sitsTypical serviceWho usually does it
Hydromechanical grease interceptor (under-sink or in-floor trap)Inside the kitchen, near the three-compartment sink or dishwasherFrequent cleaning by kitchen staff or a contracted service; inspection of baffles and flow controlStaff for routine cleaning; plumber for installation, repair and flow control fittings
Gravity grease interceptorOutside, usually buried, serving the whole kitchenPump-out by a licensed hauler on a set schedule; inspection of tees, baffles and lidsLicensed liquid waste hauler; plumber for repairs and line work
Kitchen drain linesBetween fixtures and the interceptor, and from the interceptor to the sewerJetting on a schedule; camera inspection after backupsPlumber
Sampling ports and cleanoutsDownstream of the interceptorAccess for inspectors and line cleaningPlumber installs and maintains

Hauling grease waste usually needs its own permit or registration, so many plumbing companies partner with a licensed hauler rather than buy a pump truck. The plumber owns the lines, the device installation and repairs, the schedule and the records; the hauler handles pump-outs and disposal. EPA also notes that yellow grease, used fryer oil kept out of the drains, is often collected by rendering companies for reuse[1], so make sure the kitchen has that service too.

Installing or replacing an interceptor

New restaurants, remodels and changes of use often trigger an interceptor requirement, and that is where a plumbing company earns the largest single ticket in grease work. EPA stresses that interceptors must be designed and sized so grease can cool and separate in a non-turbulent environment[1]. An undersized or badly placed unit fails inspections and backs up no matter how often it is pumped.

  1. Get the program's sizing rule and approved device list before you quote, and confirm whether the city or the plumbing code governs sizing.
  2. Count every fixture that must drain through the interceptor, and every one that must not, such as toilets and, in many programs, food waste grinders.
  3. Plan access: lids where a hauler's hose can reach, a sampling port if the program requires one, and cleanouts upstream and downstream.
  4. Submit plans for the permit with the sizing calculation attached, and book the inspection before the kitchen's opening date is fixed.
  5. Hand over a short operating guide: the cleaning schedule, who to call, and where the service records are kept.

For existing restaurants, a failed inspection is often the moment the owner decides to replace an old trap. Bring photos, the inspector's notes and two options with clear scope, and schedule the work on the kitchen's closed days.

Setting a service schedule from measurements

EPA says the required maintenance frequency depends greatly on the amount of FOG a facility generates and on the best management practices it follows, and that kitchens with good practices can reduce how often their interceptors need service[1]. Use that to set schedules honestly instead of selling the same interval to everyone.

  1. Read the ordinance

    Note any minimum pumping interval or capacity rule the program sets. Never schedule less often than the rule allows.

  2. Measure on the first visits

    Record grease layer and solids depth at each service, with the date and a photo. Three or four readings show the real accumulation rate.

  3. Set the interval

    Choose an interval that keeps the device well inside the program's limit at its busiest time of year, with a margin for holidays and events.

  4. Review twice a year

    Adjust when the menu, hours or kitchen practices change. A new fryer station or a switch to all-day breakfast changes the grease load.

  5. Report to the manager

    Send each service report the same day, with readings, photos, the hauler manifest and the next service date.

Example: a fictional plumbing company services a 120-seat restaurant with an outdoor gravity interceptor. After four monthly readings it sees the grease layer growing slowly in winter and faster in summer, when patio seating doubles covers. It sets a six-week interval from October to April and a four-week interval from May to September, documents why, and the restaurant passes its next FOG inspection without comment.

Best practices you can teach kitchen staff

Kitchen habits change the grease load more than any device. Plumbers who teach a short set of practices reduce emergency calls and give the restaurant a reason to keep them.

  • Scrape plates and pans into the trash before washing, and use sink strainers.
  • Keep fryer oil out of drains and use the rendering service's collection container.
  • Do not pour hot water or degreasers down the drain to 'flush' grease; they only move it further down the line.
  • Clean under-sink traps on the schedule posted next to the sink, and record each cleaning.
  • Report slow drains early, before a backup during dinner service.

Post a one-page laminated sheet by the dish area with the practices above, the service schedule and your company's number. Inspectors notice it, and so do new kitchen managers.

Scheduling around service hours

A restaurant cannot shut down at noon for a jetting crew. Book planned work before opening or after close, and agree in the service contract which hours count as standard and which carry an after-hours rate. Labor is a large part of the cost of these visits: average hourly earnings at plumbing, heating and air-conditioning contractors were $42.38 in September 2026[3], so a contract that pays for crews to work early mornings has to reflect that.

Managers are busy and often do not pick up unknown numbers; Pew found 80% of Americans don't generally answer calls from unknown numbers[4]. Confirm visits by text the day before from a saved number, name the restaurant and the time, and ask who will unlock the back door.

  1. 'Hi, this is the plumbing team for your grease interceptor service. We are booked for tomorrow at 6 a.m. Who will let us in at the back door?'
  2. 'Our report from today is attached: grease and solids readings, photos and the hauler's manifest. Your next service is booked for the date on the report.'
  3. 'Your kitchen line at the dish station is slowing. We recommend jetting it on your next closed day before it backs up during service.'

Growing the restaurant line

Restaurants buy from vendors they trust during a crisis. Win the first emergency by showing up fast and leaving a clear report, then offer the planned service agreement. Bundle jetting, interceptor coordination and fixture repairs into one schedule so the manager has a single vendor and a single set of records.

Restaurant groups and food halls often sit inside multifamily or mixed-use buildings; see multifamily plumbing service. Backflow testing is another recurring requirement for commercial kitchens; our guide to a recurring backflow testing program covers how to build it alongside grease work.

Frequently asked questions

How often should a restaurant grease trap be cleaned?

It depends on the kitchen's grease load, its practices and the local ordinance. EPA says required maintenance frequency depends greatly on the FOG a facility generates and the best practices it follows[1]. Measure accumulation and never go below the local minimum.

Can a plumber pump a grease interceptor?

Hauling grease waste usually requires a separate hauler permit or registration. Many plumbers partner with a licensed hauler and handle the lines, repairs, schedule and records themselves.

What records do FOG inspectors ask for?

Typically dated service reports, hauler manifests, the maintenance schedule and sometimes staff cleaning logs for under-sink traps. Keep copies for the period your program requires.

Why do restaurant drains keep clogging after jetting?

Usually because grease is still entering the drains: missing strainers, fryer oil poured down the sink, or an undersized or poorly maintained interceptor. Fix the source and the jetting interval gets longer.

References

  1. U.S. Environmental Protection Agency (2012). Controlling Fats, Oils, and Grease Discharges from Food Service Establishments (EPA-833-F-12-003) (opens in a new tab) โ†‘

  2. National Restaurant Association (2026). State of the Restaurant Industry (opens in a new tab) โ†‘

  3. U.S. Bureau of Labor Statistics, Current Employment Statistics (2026). Average hourly earnings of all employees, plumbing, heating, and air-conditioning contractors, not seasonally adjusted (CEU2023822003) (opens in a new tab) โ†‘

  4. Pew Research Center (2020). Most Americans don't answer cellphone calls from unknown numbers (opens in a new tab) โ†‘

Book a demo

See Ava handle your calls.

Book a short demo. Weโ€™ll walk through your calls and workflow, and agree what Ava should take care of.

Book a demo