Metrics finance

Truck stock inventory control and shrinkage

Control plumbing truck stock and shrinkage with min/max levels, cycle counts, a restocking routine and a few metrics that show where parts go missing.

AssistCall research teamPublished Reviewed by Faruque Amin, VP of Sales and Marketing6 min read

On this page
  1. Why truck stock deserves attention
  2. Where shrinkage comes from
  3. Setting min and max levels
  4. Stock tiers and how to control each
  5. Cycle counts instead of annual counts
  6. Example: one month of counts
  7. Rising part costs raise the stakes
  8. A restocking routine that works
  9. Rules for technicians that actually stick
  10. Metrics to watch
  11. Frequently asked questions
  12. References
Metrics finance: Truck stock inventory control and shrinkageArticle coverMETRICS FINANCETruck stock inventorycontrol and shrinkageAva for PlumbersInsightsMetrics finance: Truck stock inventory control and shrinkageArticle coverMETRICS FINANCETruck stock inventorycontrol and shrinkageAva for Plumbers

Key takeaways

  • Truck stock is cash on wheels; treat each van as a small warehouse with a standard list, min/max levels and a count schedule.
  • Most shrinkage is unbilled parts, not theft: parts installed but never added to the invoice.
  • Rotating cycle counts, a few bins per truck each week, catch problems without a full stop-everything count.
  • Part costs are climbing: the producer price index for plumbing fixtures and fittings rose about 34% between September 2019 and September 2026[1].

Why truck stock deserves attention

A service van carries the parts that decide whether a job is finished today or tomorrow. Stock it too thinly and technicians make parts runs or schedule return visits. Stock it too heavily and cash sits in bins, parts get damaged rolling around and nobody knows what is really on board. Some plumbers travel to worksites every day[2], so the van is effectively their warehouse, and it deserves the same controls as one.

The goal is simple to say and hard to do: the right parts, in the right quantities, on every truck, with every part that leaves the truck ending up on an invoice or a documented return. Getting close to that improves first-time fixes, cuts parts runs and recovers margin that is otherwise lost without anyone noticing.

Where shrinkage comes from

  • Unbilled parts. A technician installs a supply line, a few fittings and a shutoff valve but bills only the main part. This is usually the largest source of loss.
  • Untracked transfers. Parts move between trucks on a busy day and nobody records it, so one truck looks short and another looks full.
  • Warranty and callback use. Parts used on no-charge returns are real costs that should be charged to the original job, not lost.
  • Damage and spoilage. Cracked fittings, crushed boxes and expired sealants that never get written off.
  • Personal use and theft. Less common than owners fear, but real; clear rules and regular counts deter most of it.
  • Phantom stock. Parts the system thinks are on the truck but are not, often because returns to the supply house were never entered.

Setting min and max levels

  1. Pull six to twelve months of usage

    From job records, list every part used by service trucks, with quantity per month.

  2. Rank by frequency, not cost

    The parts used most often belong on every truck. Expensive but rare items usually belong in the warehouse.

  3. Set the minimum

    Cover the usage you expect between restocks, plus a small buffer. For a weekly restock, the minimum is roughly one week of typical use.

  4. Set the maximum

    Limit it by space and by cash. A max that is too high just stores cash on the truck.

  5. Standardize by truck type

    Build one list for service vans and another for drain or install trucks. Allow a short personal list for each technician's specialties.

  6. Review quarterly

    Add parts that caused return visits and remove ones nobody has touched in months.

Stock tiers and how to control each

Truck stock tiers and matching controls
TierExamplesControl
High use, low costFittings, supply lines, wax rings, cartridgesMin/max with weekly restock; count by bin
Medium use, medium costValves, flappers, disposal parts, pressure relief valvesMin/max; count monthly
Low use, high costWater heater parts, specialty valves, pumpsWarehouse or order per job; scan to the job
Tools and equipmentCameras, locators, jetters, press toolsAsset tag, sign-out log, serial numbers
ConsumablesSolder, flux, thread sealant, ragsRestock by kit; recover through a materials line

Cycle counts instead of annual counts

A full count of every truck once a year shows how much went missing but not when or why. Cycle counting spreads the work out: each week, count a few bins on each truck, rotating so every bin is counted at least once a quarter and high-use bins monthly. Counts take minutes and fit into the restock visit.

  • Count before restocking, not after, so the count reflects real use.
  • Compare the count with the system quantity and record the difference immediately.
  • Look for patterns: one technician, one part family, one day of the week.
  • Investigate any part with repeated shortages before adjusting the system to match.
  • Do a full count twice a year for accounting, and use cycle counts in between.

Example: one month of counts

Example: a fictional six-van shop runs cycle counts on its top 40 parts for a month.

Example cycle count results, fictional data
Part familySystem valueCounted valueDifference
Supply lines and connectors$1,840$1,410-$430
Brass fittings$2,960$2,520-$440
Faucet cartridges$1,380$1,340-$40
Shutoff valves$1,120$860-$260
Toilet repair parts$940$930-$10

Example, continued: the shortages cluster in small, frequently used parts that technicians add during a repair without thinking of them as billable. The fix is a short list of add-on parts in the field app with one-tap billing, plus a reminder in the job close checklist. The next month's difference falls by more than half, and the parts now appear on invoices instead of in the shrinkage line.

Rising part costs raise the stakes

Every missing part costs more than it used to. The producer price index for plumbing fixtures and fittings rose from 284.1 in September 2019 to 381.3 in September 2026, an increase of about 34%[1]. The index for copper and brass mill shapes, the metal behind much pipe and fitting stock, rose about 30% in the year to September 2026[3].

Producer price index: plumbing fixtures and fittingsSeptember of each year; producer price index level
Producer price index: plumbing fixtures and fittingsLine chart. 2019: 284.1; 2020: 289.6; 2021: 297.4; 2022: 329.6; 2023: 334.4; 2024: 340.4; 2025: 360.5; 2026: 381.3.250300350400201920202021202220232024202520262019: 284.12020: 289.62021: 297.42022: 329.62023: 334.42024: 340.42025: 360.52026: 381.3381.3284.1Producer price index: plumbing fixtures and fittingsLine chart. 2019: 284.1; 2020: 289.6; 2021: 297.4; 2022: 329.6; 2023: 334.4; 2024: 340.4; 2025: 360.5; 2026: 381.3.25030035040020192021202320262019: 284.12020: 289.62021: 297.42022: 329.62023: 334.42024: 340.42025: 360.52026: 381.3381.3284.1

Source: U.S. Bureau of Labor Statistics, via Federal Reserve Bank of St. Louis (FRED), 2026[1]

Show the data
PeriodValue
2019284.1
2020289.6
2021297.4
2022329.6
2023334.4
2024340.4
2025360.5
2026381.3

Trade policy adds pressure. A presidential proclamation imposed a 50% tariff on the copper content of semi-finished copper products and copper-intensive derivative products from August 1, 2025[4]. When prices move this fast, update the cost of truck stock in your system at least quarterly so job costs and inventory values stay accurate, and work with your supply house on price notices for your top parts.

A restocking routine that works

  • Restock on a fixed day and time per truck, from a pick list generated from the week's job usage.
  • Have the warehouse or a designated person restock, not each technician after hours.
  • Scan or sign for every part that goes onto a truck, so the system matches reality.
  • Stage parts for the next day's booked installs separately from general stock.
  • Return excess and damaged parts to the warehouse on the same visit, with a record.

A parts run is expensive. Average hourly earnings at plumbing, heating and AC contractors were $42.38 in September 2026, preliminary[5], and a supply house trip in the middle of the day can cost an hour of a technician's time plus fuel, before counting the job slot it pushes later.

Rules for technicians that actually stick

Inventory rules fail when they add work at the end of a long day. Keep them few, make them fast and explain why each one exists. A technician who understands that an unbilled valve comes straight out of the margin that funds their raise is far more likely to tap it onto the invoice.

  • Every part used goes on the job, even if it is not charged to the customer, so usage data stays accurate.
  • Transfers between trucks are logged in the app on the spot, with both technicians' names.
  • Damaged or defective parts go into a marked return bin, never back into stock.
  • Personal tool and part purchases are kept off company accounts.
  • Anything taken from the warehouse after hours is signed out on the sheet by the door.

Pair the rules with something technicians want: a clean, labelled van with the parts they actually use. Shops that build a standard bin layout, so every van has fittings in the same place, often see restocking get faster and counts get more accurate within a few weeks, because missing items are obvious at a glance.

Metrics to watch

  • Shrinkage rate: counted shortage value divided by parts used, by truck and part family.
  • Fill rate: share of jobs completed without a parts run or a return for a part.
  • Parts runs per technician per week, from GPS or reason codes.
  • Truck stock value per van against the target.
  • Parts billed as a share of parts issued, which shows unbilled usage directly.

Talk about the results with technicians as a shared problem. Most want a well-stocked truck as much as the owner does, and they know which parts they run out of. Ask for their list every quarter, and show them how unbilled parts affect the margins that fund raises and new equipment. Inventory control links closely to first-time fix, seasonal inventory planning and the cost side of running each van.

Frequently asked questions

How often should plumbing trucks be restocked?

Weekly works for most service vans, with a quick daily top-up for high-use parts in busy seasons. Set min/max levels to match the restock interval.

What is a normal amount of truck stock shrinkage?

There is no reliable public benchmark. Measure your own shrinkage by part family through cycle counts and aim to bring it down each quarter, starting with unbilled parts.

Should technicians be charged for missing stock?

Be careful. Deductions from pay can raise wage-and-hour issues, and most shrinkage is a process problem. Fix billing and counting first, and get advice before any deduction policy.

References

  1. U.S. Bureau of Labor Statistics, via Federal Reserve Bank of St. Louis (FRED) (2026). Producer Price Index by Commodity: Metals and Metal Products: Plumbing Fixtures and Fittings (WPU105) (opens in a new tab) โ†‘

  2. U.S. Bureau of Labor Statistics (2025). Occupational Outlook Handbook: Plumbers, Pipefitters, and Steamfitters (opens in a new tab) โ†‘

  3. U.S. Bureau of Labor Statistics, via Federal Reserve Bank of St. Louis (FRED) (2026). Producer Price Index by Commodity: Metals and Metal Products: Copper and Brass Mill Shapes (WPU102502) (opens in a new tab) โ†‘

  4. The White House (2025). Adjusting Imports of Copper into the United States (Proclamation, July 30, 2025) (opens in a new tab) โ†‘

  5. U.S. Bureau of Labor Statistics, Current Employment Statistics (2026). Average hourly earnings of all employees, plumbing, heating, and air-conditioning contractors, not seasonally adjusted (CEU2023822003) (opens in a new tab) โ†‘

Book a demo

See Ava handle your calls.

Book a short demo. Weโ€™ll walk through your calls and workflow, and agree what Ava should take care of.

Book a demo